Geeetech A10 firmware Marlin 1.1.9

Moderator: vert

User avatar
_kaktus_
Site Admin
Posts: 1254
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Geeetech A10 firmware Marlin 1.1.9

Post by _kaktus_ » Sun Nov 18, 2018 9:49 pm

:mrgreen:

Wooow :!:

Another novelty, new versions of controllers grow like mushrooms after the rain. :D
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

vert
Site Admin
Posts: 873
Joined: Wed Nov 21, 2018 3:50 pm
Location: Marlin Dev

Re: Geeetech A10 firmware Marlin 1.1.9

Post by vert » Sat Nov 24, 2018 6:56 pm

Would be nice if Geeetech would officially post a v1.1.9 firmware.

Lakiluke
Posts: 2
Joined: Sun Nov 25, 2018 7:10 pm

Re: Geeetech A10 firmware Marlin 1.1.9

Post by Lakiluke » Sun Nov 25, 2018 7:18 pm

Hello everyone,
I have the software installed on my a10. Why does he start at bed levels in the middle of the heating bed and leaves out the left half of the heating bed? what are those settings for Fade Height and Bed Z? What is the setting set home offset? :?

vert
Site Admin
Posts: 873
Joined: Wed Nov 21, 2018 3:50 pm
Location: Marlin Dev

Re: Geeetech A10 firmware Marlin 1.1.9

Post by vert » Sun Nov 25, 2018 10:03 pm

i found aarlis version on page 3 of this post worked really well.

ebam2014
Posts: 40
Joined: Fri Nov 02, 2018 5:06 pm

Re: Geeetech A10 firmware Marlin 1.1.9

Post by ebam2014 » Wed Nov 28, 2018 1:35 am

So can I get an actual helpful answer


can I flash this firmware on my A10 with the gt2560 rev 6??????

vert
Site Admin
Posts: 873
Joined: Wed Nov 21, 2018 3:50 pm
Location: Marlin Dev

Re: Geeetech A10 firmware Marlin 1.1.9

Post by vert » Wed Nov 28, 2018 1:54 am

The op firmware didn't work very well on my gt2560 v3.0 board arrli's did. when i reverted to official firmware the bootloader corrupted it's common and a risk taken with each flash. honestly the geeetech community is very small literally less then 10 people posting within the last like week including admins. i went through and answered as many posts as i could recently and keep in mind its night time in china when its day time in America its 2:30am in china atm support is likely sleeping.

User avatar
William
Site Admin
Posts: 4984
Joined: Tue Jun 07, 2016 9:38 am

Re: Geeetech A10 firmware Marlin 1.1.9

Post by William » Wed Nov 28, 2018 9:48 am

1.Marlin 1.1.8 for A10 exist some problem,need to fix it at first.
2.We have got the feedback of these. When we finished it,we will release it.
We won't release it if we didn't test finished it.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Rogeralcon
Posts: 5
Joined: Sun Dec 02, 2018 10:00 am

Re: Geeetech A10 firmware Marlin 1.1.9

Post by Rogeralcon » Sun Dec 09, 2018 4:02 am

Does this firmware work with the BLTOUCH?

vert
Site Admin
Posts: 873
Joined: Wed Nov 21, 2018 3:50 pm
Location: Marlin Dev

Re: Geeetech A10 firmware Marlin 1.1.9

Post by vert » Sun Dec 09, 2018 6:17 am


Rogeralcon
Posts: 5
Joined: Sun Dec 02, 2018 10:00 am

Re: Geeetech A10 firmware Marlin 1.1.9

Post by Rogeralcon » Sun Dec 09, 2018 1:20 pm

:)
vert wrote:
Sun Dec 09, 2018 6:17 am
mine does.
http://www.geeetech.com/forum/viewtopic ... 98&t=61991

Post Reply

Who is online

Users browsing this forum: No registered users and 6 guests