Page 6 of 8

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Tue Nov 13, 2018 2:22 pm
by ebam2014
how do I do this?

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Tue Nov 13, 2018 3:12 pm
by _kaktus_
Hello.
:mrgreen:

You need to look carefully at the controller board.
There is a mark on the top and bottom.

In my case it looks like this:
wycinek_GTM32Pro_vB.png
wycinek_GTM32Pro_vB.png (759.71 KiB) Viewed 13867 times

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Wed Nov 14, 2018 12:17 am
by William
_kaktus_ wrote:
Tue Nov 13, 2018 3:12 pm
Hello.
:mrgreen:

You need to look carefully at the controller board.
There is a mark on the top and bottom.

In my case it looks like this:wycinek_GTM32Pro_vB.png
Good idea of it! :D

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Wed Nov 14, 2018 4:33 am
by gdachs
ebam2014 wrote:
Wed Nov 07, 2018 3:41 am
do all A10s have mega board?
I am not aware of an A10s made by Geeetech. There exists printers named A10s, but they are not made by Geeetech and seemed to be brandless.
So you might be in the wrong forum.

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Wed Nov 14, 2018 9:17 am
by William
gdachs wrote:
Wed Nov 14, 2018 4:33 am
ebam2014 wrote:
Wed Nov 07, 2018 3:41 am
do all A10s have mega board?
I am not aware of an A10s made by Geeetech. There exists printers named A10s, but they are not made by Geeetech and seemed to be brandless.
So you might be in the wrong forum.
Maybe he means the A10 series printer :mrgreen:

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Wed Nov 14, 2018 2:34 pm
by ebam2014
sorry should I have put A10's????????????? would that have helped!

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Wed Nov 14, 2018 9:14 pm
by gdachs
ebam2014 wrote:
Wed Nov 14, 2018 2:34 pm
sorry should I have put A10's????????????? would that have helped!
Ah, it is the plural of A10, sorry for my message.

Gerald

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Thu Nov 15, 2018 4:12 pm
by ebam2014
gdachs wrote:
Wed Nov 14, 2018 9:14 pm
ebam2014 wrote:
Wed Nov 14, 2018 2:34 pm
sorry should I have put A10's????????????? would that have helped!
Ah, it is the plural of A10, sorry for my message.

Gerald
lol just a simply misunderstanding... :D :D :D :D

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Sun Nov 18, 2018 7:10 pm
by T3ste
Hello,

i have a brannd new A10 with filament detector. My board is a GT2560V3.
Is this firmware for all board revisions?
Can i use a 3D-Touch sensor with this firmware (without to change the source code)?
Is this firmware maintained at github?
Btw: Why i always have to set that the filament sensor in the printer settings to activate it (after every switch on the device)?
Thank you very much!

@Michael: thanks for making and sharing your firmware!

Best regards,
Tino

Re: Geeetech A10 firmware Marlin 1.1.9

Posted: Sun Nov 18, 2018 7:38 pm
by ebam2014
_kaktus_ wrote:
Tue Nov 13, 2018 3:12 pm
Hello.
:mrgreen:

You need to look carefully at the controller board.
There is a mark on the top and bottom.

In my case it looks like this:wycinek_GTM32Pro_vB.png
board is the gt2560 rev 6