Geeetech 3D Wifi Module For 3D app does not work

Post Reply
vap38
Posts: 23
Joined: Wed Sep 04, 2019 3:41 am

Geeetech 3D Wifi Module For 3D app does not work

Post by vap38 » Thu Oct 17, 2019 3:00 pm

Hello,
I can not connect to WiFi the Geeetech 3D Wifi Module For 3D!
the GEEETECH A10M printer is connected to the box and recognized by the application.
the 3D WIFI connects to the phone's IP address 192.168.4.2 wifi.
Then the WIFI connection fails on my account FREE impossible to connect?
I tried on 3 different phones in WIFI 2.4 GHz without success.
The router detects the 3DWIFI on the IP address.
thank you for proposing me a solution
cordially

User avatar
William
Site Admin
Posts: 6338
Joined: Tue Jun 07, 2016 9:38 am

Re: Geeetech 3D Wifi Module For 3D app does not work

Post by William » Thu Oct 17, 2019 3:31 pm

:D Hi,When you configure 3d wifi, the light flashes quickly and enters the configuration state.
You can refer to this: https://www.youtube.com/watch?v=FguzMjI ... e=youtu.be
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

vap38
Posts: 23
Joined: Wed Sep 04, 2019 3:41 am

Re: Geeetech 3D Wifi Module For 3D app does not work

Post by vap38 » Thu Oct 17, 2019 10:40 pm

thanks for the video,
i did exactly as on the video and i am still in check when i ;) write my internet access on freebox rejection of the connection despite everything is right!
a +

jenniferaniston
Posts: 1
Joined: Tue Nov 17, 2020 3:27 pm
Location: London
Contact:

Re: Geeetech 3D Wifi Module For 3D app does not work

Post by jenniferaniston » Tue Nov 17, 2020 3:39 pm

Use a pin to press and hold the hole marked "set" until the Wi-Fi indicator dims and flashes quickly. Loosen the overhead nails and 3D Wi-Fi will enter the configuration mode. Source: pay for essay by UK Writing experts.

Shieldss
Posts: 1
Joined: Mon Jan 11, 2021 1:54 pm

Re: Geeetech 3D Wifi Module For 3D app does not work

Post by Shieldss » Mon Jan 11, 2021 1:58 pm

vap38 wrote:
Thu Oct 17, 2019 3:00 pm
Hello,
I can not connect to WiFi the Geeetech 3D Wifi Module For 3D!
the GEEETECH A10M printer is connected to the box and recognized by the application.
the 3D WIFI connects to the phone's IP address 192.168.4.2 wifi.
Then the WIFI connection fails on my account FREE impossible to connect?
I tried on 3 different phones in WIFI 2.4 GHz without success.
The router detects the 3DWIFI on the IP address.
thank you for proposing me a solution Great Lakes Login
cordially
Connect your 3D printer to the USB port of 3D WiFi Module with your USB
cable for data transmission. Use the power cable to connect 3D WiFi Module with your
adapter to power it up.
Please check if the three indicator lights are on: Wi-Fi, USB, Power source from
left to right orderly. Insert the TF card into the slot
Long press the hole labeled with “set”with a pin, until the Wi-Fi light turns dim
and flickers quickly. Loosen the pin and 3D Wi-Fi will enter the config mode.
Note: If you do not loosen the pin, the light will flicker slowly to enter the reset mode.

tommartin
Posts: 2
Joined: Tue Jan 19, 2021 6:07 pm

Re: Geeetech 3D Wifi Module For 3D app does not work

Post by tommartin » Tue Jan 19, 2021 6:10 pm

Happy Adventure’s dune buggy Dubai tours furnish you with a novel chance to find the Dubai desert under the direction of our experienced and expert tour guides. Since our buggies are equipped with cutting edge security highlights,

Post Reply