BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Moderator: _kaktus_

Ziad
Posts: 6
Joined: Sun Nov 03, 2019 8:57 pm

BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by Ziad » Thu Nov 07, 2019 12:42 am

Can anyone help me how to conect bl touch to the board gtm32 vb and which software to burn, please

User avatar
_kaktus_
Site Admin
Posts: 1258
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by _kaktus_ » Thu Nov 07, 2019 5:17 am

Hello.
:mrgreen:

I can only say that:
Company firmware, firmware doesn't support this gadget.


But I'm sure you know that. :roll:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Ziad
Posts: 6
Joined: Sun Nov 03, 2019 8:57 pm

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by Ziad » Thu Nov 07, 2019 8:29 pm

No, I didn't know, :shock:
So which board should I buy now :cry:

User avatar
_kaktus_
Site Admin
Posts: 1258
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by _kaktus_ » Fri Nov 08, 2019 3:43 am

Hi.
:mrgreen:
You don't have to make any extra purchases.
Get interested in the alternative version of the firmware. ;)

Personally, I think that "automatic" levelling is not indispensable in this model.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Ziad
Posts: 6
Joined: Sun Nov 03, 2019 8:57 pm

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by Ziad » Fri Nov 08, 2019 10:02 pm

Thanks a lot for your concern n all Time replying me.
Could you please please advise me, which firmware should I install.

User avatar
_kaktus_
Site Admin
Posts: 1258
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by _kaktus_ » Sat Nov 09, 2019 5:39 am

Hi.
:mrgreen:

You can use the procedure from friend Tparent, as described in our forum. You can also try out compilations from the vert colleague.
Everything is in one topic. :D

These presentations are related to Marlin firmware version for MCU 32bit.

However, I suppose this modification will deprive you of the built-in ability to mix colors. :roll:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Ziad
Posts: 6
Joined: Sun Nov 03, 2019 8:57 pm

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by Ziad » Thu Nov 14, 2019 10:28 pm

OK thanks for all info, another issue am having is, sometimes the printer stop while printing, heat temp stiil on and still connected to pc, even with sd memory card loaded, thanks to help me

User avatar
William
Site Admin
Posts: 6330
Joined: Tue Jun 07, 2016 9:38 am

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by William » Fri Nov 15, 2019 9:15 am

:D Hi, If you print for a long time,
It is best to slice the print model and save it to the sd card for printing.
Does this happen often?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Ziad
Posts: 6
Joined: Sun Nov 03, 2019 8:57 pm

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by Ziad » Sat Nov 16, 2019 5:45 pm

Yes 1 out of 6,
Even for a print of 10min,
Imagine my frustration if it was a printing of 2hrs, lots filament wasted +Time.
Have anyone having this issue

User avatar
_kaktus_
Site Admin
Posts: 1258
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: BL TOUCH prusa i3 m201 dual extruder gtm32 Pro vb,

Post by _kaktus_ » Sun Nov 17, 2019 3:16 pm

Hi.
:mrgreen:

Read the information from our subforum about the M201 model.
Two cases have been identified and resolved by me. :D

I don't know if you know but a stopped/interrupted printout can be continued. :idea:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Post Reply

Who is online

Users browsing this forum: No registered users and 18 guests