Large z-wobble, x-y axis inflation

Post Reply
k40z
Posts: 6
Joined: Tue Aug 07, 2018 6:19 pm

Large z-wobble, x-y axis inflation

Post by k40z » Wed Aug 08, 2018 3:48 pm

Hi there.
I've a problem with verticals objects.
They are printed with horizontal deformations and appears like a cyclical inflating/misalignment over x and y directions.
I need help.
Thank you.

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Large z-wobble, x-y axis inflation

Post by _kaktus_ » Wed Aug 08, 2018 4:22 pm

Hi
:mrgreen:

Can you post a photo of your model?
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

k40z
Posts: 6
Joined: Tue Aug 07, 2018 6:19 pm

Re: Large z-wobble, x-y axis inflation

Post by k40z » Wed Aug 08, 2018 9:57 pm

Files attached.
Thanks for you reply
Attachments
FB_IMG_1533667642697.jpg
FB_IMG_1533667642697.jpg (151.55 KiB) Viewed 8524 times
FB_IMG_1533667510793.jpg
FB_IMG_1533667510793.jpg (301.27 KiB) Viewed 8524 times

k40z
Posts: 6
Joined: Tue Aug 07, 2018 6:19 pm

Re: Large z-wobble, x-y axis inflation

Post by k40z » Thu Aug 09, 2018 12:35 am

Thanks for your attention
Attachments
FB_IMG_1533667642697.jpg
Z-wobble
FB_IMG_1533667642697.jpg (151.55 KiB) Viewed 8524 times

MrFranke
Posts: 3
Joined: Thu Dec 27, 2018 2:23 am

Re: Large z-wobble, x-y axis inflation

Post by MrFranke » Thu Dec 27, 2018 5:53 pm

Hi,

Did you find any solution to solve this Problem? Because I have this printer for some weeks now and have the same issue, but no solution.

Thanks

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Large z-wobble, x-y axis inflation

Post by _kaktus_ » Thu Dec 27, 2018 6:07 pm

Hi.
:mrgreen:

It looks as if the axis mechanisms still require calibration, and adjustment.

Read the subforum about the A10 and A30 models there is a lot of information about how to adjust the carriages. ;)
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

MrFranke
Posts: 3
Joined: Thu Dec 27, 2018 2:23 am

Re: Large z-wobble, x-y axis inflation

Post by MrFranke » Fri Dec 28, 2018 2:18 am

I have now read almost the entire forum, but found nothing that is helpful.
The whole system is free of play, the reels run reasonable, I only print with 30mm/s, I checked the driver voltage, nothing helps.

I am on the edge of throwing the printer in the trash

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Large z-wobble, x-y axis inflation

Post by _kaktus_ » Fri Dec 28, 2018 4:15 am

HI.
:mrgreen:

Someone wrote that the wheels of the trolley squash when not in use.
Don't throw away the equipment, treat everything as a test of your nature. ;)
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Post Reply