Connection 3DTouch sur Rostock 301 Modifié

Post Reply
User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Connection 3DTouch sur Rostock 301 Modifié

Post by Lami René » Sat Aug 26, 2017 3:00 am

Hello,
Bonjour,

You can find the original text translated into English following this original French text.

Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.

Comme je ne peux imprimer avec la tête diamant à trois (3) filaments, je l'ai remplacé par une tête chauffante mono filament avec ventilateur et une nouvelle fixation. Voir le détail des pièces et modification sur la page Web suivante :

http://forums.reprap.org/read.php?178,781375

Maintenant, comme la tête d'impression est beaucoup plus petite, je voudrais installer un capteur de nivellement Geeetech 3DTouch acheté en septembre 2016 sur cette Geeetech Rostock 301 modifiée.

Pourriez-vous m'indiquer comment connecter votre capteur de nivellement Geeetech 3DTouch sur votre carte contrôleur ou sur votre carte de l'extrudeur de votre imprimante 3D Geeetech Rostock 301 modifié et comment la configurer (logiciel et matériel) pour son utilisation avant chaque impression avec Repetier-Host ?

Cordialement,

L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello,

Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!

Since I can not print with diamond head with three (3) filaments, I replaced it with a heating head mono filament with fan and a new fixing. See details of parts and modification on the following web page:

http://forums.reprap.org/read.php?178,781375

Now, as the print head is much smaller, I would like to install a Geeetech 3DTouch leveling sensor purchased in September 2016 on this modified Geeetech Rostock 301.

Could you tell me how to connect your Geeetech 3DTouch leveling sensor to your Geeetech Rostock 301 3D Controller card or extruder card and how to configure it (software and hardware) for use before each print job with Repetier-Host?

Cordially,

The friend René
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Re: Connection 3DTouch sur Rostock 301 Modifié

Post by Lami René » Fri Sep 01, 2017 8:11 am

Hello to the technicians of Geeetch,
Bonjour aux techniciens de Geeetch,

You can find the original text translated into English following this original French text.

Vous trouverez le texte original traduit en anglais à la suite du présent texte original en français.

Bon avec une semaine d'attente d'une semaine, je suis en droit de renouveler ma demande de la procédure de branchement, de configuration et d'utilisation de votre capteur de nivellement de plateau d'impression 3DTouch sur votre imprimante Rostock 301 !

Je vous offre mes services de bêtatesteur pour vous aider à concevoir et rédiger ces procédures qui tardent depuis plus de 12 mois, ce qui est inacceptable !

Parmi mes compétences, je suis programmeur analyste et dessinateur industriel (dessin paramétrique en 3D) !

Vous n'avez qu'a demandé, mais ne restez pas à ne rien faire, pour nous vos clients, sans nous, vous n'existeriez pas comme entreprise !!!

Cordialement,

L'ami René
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Hello to the technicians of Geeetch,

Excuse me, I am unilingual francophone and I use Google translator to translate the texts of the forum in French and to write to you in English. Thank you for your understanding and your indulgence for these texts translated mechanically!

Good with one week waiting period of one week, I am entitled to renew my request for the procedure of connection, configuration and use of your 3DTouch printing tray leveling sensor on your Rostock 301 printer!

I offer my services as a beta tester to help you design and write these procedures which have been delayed for more than 12 months, which is unacceptable!

Among my skills, I am programmer analyst and industrial designer (parametric drawing in 3D)!

You only have to ask, but do not just do nothing, for us your customers, without us, you would not exist as a company !!!

Cordially,

The friend René
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

Post Reply