Page 2 of 4

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Wed Feb 11, 2015 2:29 pm
by zhangxueyou
You are welcome. Hope you enjoy your printing later.

Cheung Weng

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Thu Feb 12, 2015 11:50 am
by Anabatix
Hi,
A couple more questions.

1. I think I must cut the white plug off the 12vDC power, strip and screw into board directly? As the photo you show can't be the same board design as in the kit for Ramps 1.4... correct?
2. The 2x Z Axis stepper motors, the white plugs to connect to the Ramps board will never fit. Have you tried it on your Kit. What do you suggest for an easy fix?
3. Could you post some good photos of a completed Prusa Alu Kitset so I can check the layout is as intended. Your manual does not show board or extruder mounting etc. And cable layout around motors.
4. Could you post a Ramps 1.4 finished wiring photo as it is worth 1000 words. And will explain better the power, fan and heatbed wiring using this kitset.

Thanks,

Lee

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:42 am
by zhangxueyou
I will give you the pictures of all the wiring of all the parts. Please, you must understand my pictures because I spent a lot time assembling. If you have any problem, please reply me T_T
Ramp1.4+Mega2560
image1.png
image1.png (319.87 KiB) Viewed 31217 times
image2.png
image2.png (450.45 KiB) Viewed 31217 times
Jumper caps
image3.png
image3.png (596.52 KiB) Viewed 31217 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:45 am
by zhangxueyou
Cooling fan for mainboard
Cooling fan.png
Cooling fan.png (397.42 KiB) Viewed 31218 times
Cooling fan2.png
Cooling fan2.png (524.28 KiB) Viewed 31218 times
Extruder motor
Extruder motor wiring.png
Extruder motor wiring.png (601.39 KiB) Viewed 31218 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:49 am
by zhangxueyou
Themistor on hotbed
Thermistor on hotbed2.png
Thermistor on hotbed2.png (183.19 KiB) Viewed 31218 times
Thermistor on hotbed.png
Thermistor on hotbed.png (806.05 KiB) Viewed 31218 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:52 am
by zhangxueyou
Hotbed
hotbed.png
hotbed.png (373.92 KiB) Viewed 31218 times
hotbed wiring.png
hotbed wiring.png (345.6 KiB) Viewed 31218 times
Wirng of Endstop
wiring of endstop.png
wiring of endstop.png (557.72 KiB) Viewed 31218 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:56 am
by zhangxueyou
Power supply

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:56 am
by zhangxueyou
LCD
LCD.png
LCD.png (493.32 KiB) Viewed 31218 times
LCD wiring.png
LCD wiring.png (569.16 KiB) Viewed 31218 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 9:58 am
by zhangxueyou
Wiring of extruder
Wiring of extruder.png
Wiring of extruder.png (534.37 KiB) Viewed 31218 times
Wiring of thermistor for extruder
Wiring of themistor for Exturder.png
Wiring of themistor for Exturder.png (419.83 KiB) Viewed 31218 times

Re: Require full Prusa I3 Aluminium Kit Assembly Instruction

Posted: Fri Feb 13, 2015 10:00 am
by zhangxueyou
Switch
switch1.png
switch1.png (345.89 KiB) Viewed 31218 times
switch2.png
switch2.png (561.54 KiB) Viewed 31218 times