Easyprint software for WINDOWS

User avatar
William
Site Admin
Posts: 4367
Joined: Tue Jun 07, 2016 9:38 am

Re: Easyprint software for WINDOWS

Post by William » Fri Jan 04, 2019 9:19 am

bertie wrote:
Sat Dec 29, 2018 3:03 pm
I solved it by manually downloading and installing Visual C++ Redistributable 2015 (X86 + X64) from Microsofts website and reinstalling EasyPrint. Installing C++ via EasyPrint installer did not work for me and on my machine was only version 2017 instead of 2015.
Thx for your feedback! ;)
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

pepgra
Posts: 11
Joined: Thu Dec 20, 2018 6:51 am

Re: Easyprint software for WINDOWS

Post by pepgra » Sat Jan 05, 2019 5:19 am

Because the combo-box does not show the model A20M?

Bernhard
Posts: 1
Joined: Sun Jan 06, 2019 7:56 pm

Re: Easyprint software for WINDOWS

Post by Bernhard » Sun Jan 06, 2019 8:18 pm

Hello,
I installed the Easyprint software. I can load the 3D-files but I cannot save it as G-code.
There comes following failure notice: File C:\Users\Bernhard\AppData\Roaming\easyprint\work\composition.gcode was not found.
How can I get this file?
I use Windows 7 and Easyprint 1.2.6
Best regards

nvnazeer
Posts: 1
Joined: Sun Jan 06, 2019 11:11 pm

Re: Easyprint software for WINDOWS

Post by nvnazeer » Mon Jan 07, 2019 12:35 am

Hi, where can i get a link for the latest version of easyprint software for windows.
Are there any issues if i use this with A10M

Thanks

User avatar
_kaktus_
Site Admin
Posts: 1220
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Easyprint software for WINDOWS

Post by _kaktus_ » Thu Jan 10, 2019 1:55 am

Hello.
:mrgreen:


nvnazeer
Your question should not be asked at all. :roll:
The answer is in the first post of this topic.

If you are an attentive observer you will see a location there: https://www.geeetech.com/firmware/
As of today, the latest version has been announced 2018-09-06.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Achim2019
Posts: 1
Joined: Sun Jan 13, 2019 7:20 am

Re: Easyprint software for WINDOWS

Post by Achim2019 » Thu Jan 17, 2019 4:08 am

Hi, I'm new here. I miss the download button for Easyprint Software, english version.
Thx in advance!

WikiBrikoFix
Posts: 2
Joined: Sat Jan 26, 2019 5:08 am

Re: Easyprint software for WINDOWS

Post by WikiBrikoFix » Sat Feb 02, 2019 5:23 am

For all that have problems with EasyPrint 3D: the correct installation procedure is

1) Remove all C++ Redistributable version 2015 and 2017
2) Manual install the C++ Redistributable 2015 for x86 and x64 downloaded from here
https://www.microsoft.com/en-us/downloa ... x?id=52685
3) Install EasyPrint 3D (custom install, deselect C++ 2015 Redistributable packages)
4) reinstall C++ Redistributable 2017 removed on step 1
https://support.microsoft.com/it-it/hel ... -downloads

I have done it, after many problems, and now EasyPrint run correctly, without cura engine error and save error.

bye!

User avatar
William
Site Admin
Posts: 4367
Joined: Tue Jun 07, 2016 9:38 am

Re: Easyprint software for WINDOWS

Post by William » Wed Feb 13, 2019 1:22 pm

WikiBrikoFix wrote:
Sat Feb 02, 2019 5:23 am
For all that have problems with EasyPrint 3D: the correct installation procedure is

1) Remove all C++ Redistributable version 2015 and 2017
2) Manual install the C++ Redistributable 2015 for x86 and x64 downloaded from here
https://www.microsoft.com/en-us/downloa ... x?id=52685
3) Install EasyPrint 3D (custom install, deselect C++ 2015 Redistributable packages)
4) reinstall C++ Redistributable 2017 removed on step 1
https://support.microsoft.com/it-it/hel ... -downloads

I have done it, after many problems, and now EasyPrint run correctly, without cura engine error and save error.

bye!
;)
Thanks for sharing your experience!
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

schlulou
Posts: 9
Joined: Thu Mar 07, 2019 7:32 am

Re: Easyprint software for WINDOWS

Post by schlulou » Sat Mar 23, 2019 3:05 am

Is this software still being worked on or can it be considered abandoned? What's the latest version? Too many sources to keep track of. Forum, apache listing, download section etc. My Version has no idea the A10M exists...

User avatar
William
Site Admin
Posts: 4367
Joined: Tue Jun 07, 2016 9:38 am

Re: Easyprint software for WINDOWS

Post by William » Tue Mar 26, 2019 2:22 pm

schlulou wrote:
Sat Mar 23, 2019 3:05 am
Is this software still being worked on or can it be considered abandoned? What's the latest version? Too many sources to keep track of. Forum, apache listing, download section etc. My Version has no idea the A10M exists...
Geeetech official won't updates EP, I recommended you to use Cura, Slic3r, etc.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Locked

Who is online

Users browsing this forum: No registered users and 16 guests