How to burn the firmware for GTM32 Pro VB

User avatar
William
Site Admin
Posts: 4640
Joined: Tue Jun 07, 2016 9:38 am

Re: How to burn the firmware for GTM32 Pro VB

Post by William » Fri Nov 30, 2018 11:09 am

jonatan wrote:
Fri Nov 30, 2018 11:05 am
no entiendo el punto 2.2 Inserte una tapa de puente correspondiente en el arranque0 de la placa.
me podria explicar mejor? no entiendo que ahi que hacer.
tengo este error
Burn the bootloader and then upload the firmware.
Then you need to install the drivers for this board,set the baud rate to 115200
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
_kaktus_
Site Admin
Posts: 1237
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: How to burn the firmware for GTM32 Pro VB

Post by _kaktus_ » Fri Nov 30, 2018 1:14 pm

Hi.
:mrgreen:

Do you know what a jumper cap is?
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

jonatan
Posts: 8
Joined: Tue Aug 14, 2018 6:43 am

Re: How to burn the firmware for GTM32 Pro VB

Post by jonatan » Sat Dec 01, 2018 3:34 am

no tengo idea de que es o que ahi que hacer ?

jonatan
Posts: 8
Joined: Tue Aug 14, 2018 6:43 am

Re: How to burn the firmware for GTM32 Pro VB

Post by jonatan » Sat Dec 01, 2018 3:49 am

ahi que sacar ese cosito negro que sale señalado en la foto ?

jonatan
Posts: 8
Joined: Tue Aug 14, 2018 6:43 am

Re: How to burn the firmware for GTM32 Pro VB

Post by jonatan » Sat Dec 01, 2018 3:55 am

o ahi que ponerle algo ahi? donde lo consigo ? no se nada de esto !

jonatan
Posts: 8
Joined: Tue Aug 14, 2018 6:43 am

Re: How to burn the firmware for GTM32 Pro VB

Post by jonatan » Sun Dec 02, 2018 3:41 am

hola he echo los pasos que dice en el foro, y ahora no me anda el lcd y el ventilador del extrusor.
que pudo aver pasado ?

hitmano
Posts: 3
Joined: Wed Dec 19, 2018 4:29 pm

Re: How to burn the firmware for GTM32 Pro VB

Post by hitmano » Wed Mar 27, 2019 3:51 am

It would be extraordinary if these two open source sheets could bolster Marlin 2.x 32bit rendition. I have no clue about coding. However, this would be amazing if Geeetech or clients who can code would make Marlin 2.x to be good with the GTM32 sheets. So much conceivable outcomes and highlights would open up for the clients and furthermore for Marlin. I've seen this issue posted on the Smartto firmware store which as I would see it would have a place here, it's anything but a firmware issue/highlight however increasingly like an equipment issue.

Locked

Who is online

Users browsing this forum: salvaDI and 5 guests