Extruder Motor Not working...

Surfovod
Posts: 11
Joined: Wed May 27, 2015 1:43 pm

Re: Extruder Motor Not working...

Post by Surfovod » Mon Jul 06, 2015 1:37 pm

Thanks
All items fulfilled, but to revive the stepper motor of the extruder and failed :(
Judging by the topics on this forum I the only one who has the same problem with the 2560 GT
I'll call the customer service.

Hock
Posts: 9
Joined: Tue Jun 30, 2015 12:34 pm
Location: Kuching, Sarawak, Malaysia

Re: Extruder Motor Not working...

Post by Hock » Mon Jul 06, 2015 2:00 pm

Eric wrote:Dear friends
please try the following ways to solve the problem.
1.the extruder will move until the temperature was raise to 180 degrees for PLS,240 degrees ABS.Please check whether the extruder is heated up.
2.please swap the driver board with x-axis,if x-axis is working,the driver board is good.
3.please connnect the motor wire of the extruder to x-axis .if working,the stepper motor is good.
4.please re=download the firmware.Please refer to attachment.
If all above methods do not work,please contact the customer service.
firmware uploaded...
Also not working..............

Surfovod
Posts: 11
Joined: Wed May 27, 2015 1:43 pm

Re: Extruder Motor Not working...

Post by Surfovod » Mon Jul 06, 2015 2:40 pm

Hock
if you solve this problem, tell us how to do

Hock
Posts: 9
Joined: Tue Jun 30, 2015 12:34 pm
Location: Kuching, Sarawak, Malaysia

Re: Extruder Motor Not working...

Post by Hock » Mon Jul 06, 2015 5:32 pm

I also wish got someone tell me how to do now..... :lol:

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Extruder Motor Not working...

Post by Sherry » Mon Jul 06, 2015 5:50 pm

Hock wrote:I also wish got someone tell me how to do now..... :lol:
If reloading the firmware doesn't work,please leave the order number or contact the customer service.

Hock
Posts: 9
Joined: Tue Jun 30, 2015 12:34 pm
Location: Kuching, Sarawak, Malaysia

Re: Extruder Motor Not working...

Post by Hock » Mon Jul 06, 2015 6:09 pm

Eric wrote:
Hock wrote:I also wish got someone tell me how to do now..... :lol:
If reloading the firmware doesn't work,please leave the order number or contact the customer service.
I buy from ebay,
transaction no is : 1391549858018

Surfovod
Posts: 11
Joined: Wed May 27, 2015 1:43 pm

Re: Extruder Motor Not working...

Post by Surfovod » Mon Jul 06, 2015 9:24 pm

I've already written for service, but the response has not yet been

User avatar
Admin
Posts: 267
Joined: Wed Nov 30, 2011 9:49 am

Re: Extruder Motor Not working...

Post by Admin » Fri Jul 10, 2015 4:43 pm

Hock wrote:Hi,
I have a Acrylic Geeetech I3 Pro B With GT250 control board & A4988 motor driver,
I set up every thing , & tested....X,Y Z motor work fine,but Extruder motor not working..
temperature of extruder ..check
spring tight ..check
motor driver.. check
plug extruder motor wire to x motor slot.. check
Exchang extruder motor wire with x motor wire.... check
motor driver voltage between 0.9-1V....check

I have try all this ,but still not work....
What should I do ??
Please Help......
Thanks.....
hi, my apology for delay in reponding.these are upgraded firmwares,it could make the extruder work now,please download it if necesarry.
Attachments
GT_I3_pro_C.zip
(283.1 KiB) Downloaded 146 times
GT_I3_pro_B.zip
(283.1 KiB) Downloaded 147 times

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Extruder Motor Not working...

Post by Sherry » Fri Jul 10, 2015 4:46 pm

Surfovod wrote:I've already written for service, but the response has not yet been
hi,the upgrade firmware will help you solve the problem.please reburn the firmware in the attachment.

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Extruder Motor Not working...

Post by Sherry » Fri Jul 10, 2015 4:47 pm

Surfovod wrote:I've already written for service, but the response has not yet been
hi,the upgrade firmware will help you solve the problem.please reburn the firmware in the attachment.
Attachments
GT_I3_pro_C.zip
(283.1 KiB) Downloaded 175 times
GT_I3_pro_B.zip
(283.1 KiB) Downloaded 142 times

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest