Page 3 of 33

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Tue Oct 25, 2016 8:54 pm
by JohnQuix
@William

Are there any instructions on how to hook the 3DTouch up to a MeCreator 2?

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Tue Oct 25, 2016 10:21 pm
by UndCon
HI!

I installed my Sensor and modified the firmware (I hope correctly, the instructions are not very easy to understand)

Anyway...

When I power up I get the selftest 3 time movement.

When I try to send any command from Repetierhost in the G-code window it says nothing and do nothing.

Not even the alarm test works.

When I try to move Home in all axis Z says "Z probe out. bed"

In this case it doesnt matter if probe is lit or not, in or out...

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Wed Oct 26, 2016 12:36 am
by JohnQuix
@JumpBase

Thanks so much for uploading that bracket. Unfortunately I use that side for my fan. The two screw holes on the carriage fit a turbo fan perfect so I can't move the fan. :(

Back to the drawing board.

@William

Is there a guide or instructions that I can read to get the 3DTouch wired to my Me Creator 2?

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Wed Oct 26, 2016 7:35 pm
by elfag.blogg.no
It worked for one day, now it wont work at all

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Thu Oct 27, 2016 1:08 am
by UndCon
Can someone Please post their config.h and pins.h files so I can verify correct settings?

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Thu Nov 03, 2016 4:23 am
by UndCon
I found an error I made...

According to the instructions here:
http://www.geeetech.com/blog/tag/3dtouc ... ng-sensor/

I connected the 3pin BROWN - RED - ORANGE to the GT2560 board _ Not BROWN, ORANGE, RED as it is supposed to be...

I simply assumed the 3pin was a straight connector (I used a regular RC extension)


Question: Did I ruin this port on the board when ORANGE and RED got mixed up?

Question: Can I save it by using another free 3pin connector by assigning another PIN?

Question: Did I ruin the sensor ?


BR
UndCon

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Thu Nov 03, 2016 10:21 pm
by UndCon
Thx for the provided files configurationh and pins.h

This did not help me at all, I have the correct settings on my printer - but sensor does still not work.

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Fri Nov 04, 2016 11:34 am
by William
UndCon wrote:Thx for the provided files configurationh and pins.h

This did not help me at all, I have the correct settings on my printer - but sensor does still not work.
Maybe the wire order is a problem,could take a picture of your wire order?

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Fri Nov 04, 2016 5:31 pm
by UndCon
Like I wrote above I found a mistake with wires and corrected it.
/UndCon

Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer

Posted: Wed Nov 09, 2016 3:33 am
by Dppp
I purchased 3D touch sensor to my Prusa I3 Pro B and today I installed it to printer, but I was not able to get it working. When I power up printer, pin is mowing 3 times, but when I try to send any custom G-codes, nothing happens. What should I do / check next to get it working? All needed firmware modifications are done.

UndCon: Did u managed to get your sensor to working?