lcd 12864-3d

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

lcd 12864-3d

Post by cschisler » Fri Jul 19, 2019 11:49 am

i installed a new gt2560 v3 controller board. now the lcd flashes and beeps. my a20m is useless. i fashed it with different marlins with no luck. please help. the controller board has 3 red led's lit. while flashing the yellow led flash once firmware is loaded the yellow led stops flashing.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: lcd 12864-3d

Post by William » Fri Jul 19, 2019 2:20 pm

Hi, You can
  1. Reconnect the screen cable to try it out;
                
  2. go to the official website to download the firmware and then upgrade
I hope this can help you.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

Re: lcd 12864-3d

Post by cschisler » Tue Jul 23, 2019 3:38 am

thanks for the response i've done both with no luck. i was working on the system last night trying to ohm out the cable just in case it had a broken trace. not an easy task but all seemed to be connected. i did notice that the CPU on the board got very hot very quickly. even with all cables were disconnected (except for power) should the processor get that hot? it was almost too warm to touch. even the board underneath the chip got very warm. i realize that the board is acting like a heat sink but we are talking getting very warm within the 1st minute after power up. i've attached a short video of the problem in action. it is a zipped mp4 file.
Attachments
a20mlcd.zip
(9.67 MiB) Downloaded 374 times

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

Re: lcd 12864-3d

Post by cschisler » Tue Jul 23, 2019 3:40 am

where can i purchase a new lcd for this system just in case it is bad?

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

Re: lcd 12864-3d

Post by cschisler » Wed Jul 24, 2019 1:29 am

did you get a chance to view the video? could you tell me where i can purchase the lcd display? is the processor suppose to run that hot?

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: lcd 12864-3d

Post by William » Wed Jul 24, 2019 10:11 am

Hi, It looks like the screen line and the screen are not in good contact. You can try to reconnect the screen.
If you buy the screen, you can contact your sales for a detailed consultation.
By the way, if the motherboard is overheated, is there a heat sink on your driver board?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

Re: lcd 12864-3d

Post by cschisler » Wed Jul 24, 2019 12:04 pm

there is no heat sink on the processor its self. there has never been one.....should there be one from the factory? i have no idea who my sales is to contact for a new lcd.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: lcd 12864-3d

Post by William » Wed Jul 24, 2019 1:32 pm

OH, I just mean the heat sink on the drive board.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: lcd 12864-3d

Post by _kaktus_ » Wed Jul 24, 2019 3:16 pm

Hello.
:mrgreen:

If µC heats up, this is a symptom of abnormality.
If you find that it is too hot, there is a high probability that it is damaged :!:

Ask your reseller for a replacement.
If you want to buy an extra copy, ask your GT Sellers.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

cschisler
Posts: 15
Joined: Thu Mar 21, 2019 11:41 am

Re: lcd 12864-3d

Post by cschisler » Thu Jul 25, 2019 1:01 am

i ordered one last week from your store. where can i purchase the lcd display?

Post Reply