Firmware for geeetech 3D printers

Post Reply
Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Firmware for geeetech 3D printers

Post by Mark » Sat Oct 10, 2015 11:02 am

Hi guys, all the firmware for geeetech 3D printers are here,
please choose your printer type download it, tks!

Note: if you don't know how to install the firmware, come here:
1. For board GT2560 and sanguinololu:
viewtopic.php?f=13&t=17181
2.For the board GTM32 (prusa I3 M201), please come to here install the firmware:
Using ST-link: viewtopic.php?f=13&t=17173
Using USB port: viewtopic.php?f=20&t=17597
3.If your board is GTM32 pro with 3 in 1 hotend, come here to install the firmware:
viewtopic.php?f=20&t=18167
4. If your board is GTM32 PRO VB, check out this link:
viewtopic.php?f=20&t=60425
5. If one of your axis direction is reversed, check out this link:
viewtopic.php?f=17&t=17037
6. After installing the firmware, if the LCD is beeping all the time and has two rows of blocks, then you must have installed the wrong firmware, please check it agian!

1) Firmware for Prusa I3 M201
The latest version(for GTM32) :
GTM32_V1.0.5.zip
GTM32_V1.0.5
(98.94 KiB) Downloaded 6556 times
For the new board(GTM32 Pro)on M201:
gtm32_machine_m201.zip
(62.23 KiB) Downloaded 2875 times
Note:
V1.0.5 added some G-code commands on the base of V1.0.4:
M92: Set axis_steps_per_unit
M110: Set Current Line Number M500
M502: Revert to the default "factory settings."
M300: Play beep sound
M304: Set PID parameters - Bed

V1.0.4 has fixed some bugs and the pause problem in the old ones, check out this link for more details:
viewtopic.php?f=20&t=17279

The old version:
GTM32_V1.0.4.zip
GTM32_V1.0.4
(97.15 KiB) Downloaded 1905 times
GTM32_1.0.3.zip
GTM32_V1.0.3
(96.01 KiB) Downloaded 1381 times
GTM32-V1.0.0.zip
(96.05 KiB) Downloaded 1109 times
GTM32-old.zip
(92.53 KiB) Downloaded 1096 times
2) Firmware for Prusa I3 X(GT2560)
I3_pro_X.zip
(295.69 KiB) Downloaded 15526 times
if you have upgrade your pro X into a dual extruder, please use this firmware
Marlin-PI3_Pro_X2.zip
(299.37 KiB) Downloaded 4081 times
3) Firmware for Aluminum I3
For sanguinololu, you need to copy the folder named "sanguino" to the folder "hardware" of Arduino IDE.
The "sanguino" folder:
sanguino.zip
(209.25 KiB) Downloaded 402 times
Download this file and unzip it and move it to the folder "hardware".
1 for sanguinololy.jpg
1 for sanguinololy.jpg (34.93 KiB) Viewed 19354 times
Then you can use the Arduino IDE 1.0.1 to upload the firmware as the link:
viewtopic.php?f=20&t=16433
For the old aluminum i3(with printed extruder bracket and gear), use the firmware below:
aluminum I3 Ramps 1.4
PI3_Ramps14固件.rar
(199.43 KiB) Downloaded 1970 times
aluminum I3 sanguinololu
PI3_Sanguinololu固件.rar
(229.44 KiB) Downloaded 2171 times
For the full aluminum I3, use the firmware here:

for the upgraded kit using lead screw aluminum I3 Ramps 1.4
Prusa I3A 2560.zip
(281.17 KiB) Downloaded 2989 times
aluminum I3 sanguinololu
Plusa I3 A sanguinololu.zip
(242.28 KiB) Downloaded 3397 times
4) For prusa I3 A Pro with the 3-in-1 3D printer control box:
PI3A Pro.zip
prusa I3 A Pro
(375.46 KiB) Downloaded 2815 times
for the upgraded kit using lead screw:
PI3A Pro(for the upgraded kit using lead screw).zip
(375.46 KiB) Downloaded 1442 times
if you upgrade your prusa I3 A Pro with dual extruder, please download the firmware here.
PI3A_Pro2.zip
prusa I3 A Pro with dual extruder
(375.73 KiB) Downloaded 1014 times
for the upgraded kit using lead screw:
PI3A Pro2(for the upgraded kit using lead screw).zip
(375.73 KiB) Downloaded 861 times
5) Firmware for I3 pro&proB
I3 pro&proB(GT2560)
Marlin-PI3_Pro_B.zip
(299.2 KiB) Downloaded 20403 times
I3 pro&proB(ramps)
PI3B-ramps.rar
PI3B-ramps
(229.7 KiB) Downloaded 4960 times
I3 pro&proB(sanguinololu)
PI3B-Sanguino.rar
PI3B-sanguinololu
(229.88 KiB) Downloaded 3710 times
6) Firmware for I3 pro C

I3 pro C (GT2560)
Marlin_GT2560-PI3_Pro_C.zip
Marlin_GT2560-PI3_Pro_C.zip
(299.21 KiB) Downloaded 8883 times
I3 pro C (ramps)
PI3B-Ramp14-2E.rar
PI3B-Ramp14-2E.rar
(268.97 KiB) Downloaded 2502 times
I3 pro C (GT2560 A+)
I3proC ( A+ board ).zip
(311.94 KiB) Downloaded 17 times
7) Frimware for Delta G2/G2S

For plastic G2/G2S with printed plastic spider and carriages:
RKMA_GT2560_G2.zip
RKMA_GT2560_G2.zip
(283.11 KiB) Downloaded 1491 times
RKMA_GT2560_G2s.zip
(372.37 KiB) Downloaded 1473 times
For metal G2 pro/G2S pro with upgraded metal spider:
RKMB_GT2560_G2.zip
RKMB_GT2560_G2(pro).zip
(372.1 KiB) Downloaded 1717 times
RKMB_GT2560_G2S.zip
RKMB_GT2560_G2S(pro).zip
(372.37 KiB) Downloaded 3328 times
Note:
1. If you run into the problem that the G2S extruder2 drives axial motors when printing, you can try to solve it by reinstall the latest firmware above, and change some setting here: viewtopic.php?f=13&t=17064
2. The probe endstop, if you use the old firmwrare for plastic G2/G2S, X Y Z should connected to pin1 and pin3; and the new firmware for metal G2 pro/G2S pro, it should be pin1 and pin2 , the same with X Y Z endstops, you can refer to the link here:
viewtopic.php?f=13&t=17042&p=27619#p27619

8) Frimware for Me ducer
MD1_Sanguino.rar
MD1_Sanguino.rar
(268.83 KiB) Downloaded 1099 times
9) Frimware for Me creator
Me creator(ramps1.4)
ramps14.rar
ramps14.rar
(229.05 KiB) Downloaded 1443 times
Me creator(sanguinololu)
Sanguino.rar
Sanguino.rar
(229.11 KiB) Downloaded 1998 times
10) Firmware for MeCreator2(GT2560 Rev B)
MeCreator2固件.zip
(293.54 KiB) Downloaded 2693 times
11) Firmware for Rostock 301(GTM32 Pro)
The latest version(Max extruder temp 220℃):
Rostock301_V1.0.03.zip
(63.71 KiB) Downloaded 311 times
The firmware(Max extruder temp 270℃)
gtm32_machine_delta.zip
(64.11 KiB) Downloaded 144 times
The old version:
Rostock301_V1.0.02.zip
(63.58 KiB) Downloaded 2826 times
gtm32_machine_delta_V1.0.01.zip
(63.6 KiB) Downloaded 1830 times
12) Firmware for Duplicator 5
Duplicator5.zip
(285.92 KiB) Downloaded 338 times
13) Firmware for Pro W
ProW.zip
(299.49 KiB) Downloaded 750 times

mava70
Posts: 20
Joined: Sun Nov 01, 2015 8:20 am

Re: firmware for geeeteh 3D printers

Post by mava70 » Sat Nov 07, 2015 2:41 am

hello in PI3B-ramps.rar there is not Marlin.ino how to compile?

thanks

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: firmware for geeeteh 3D printers

Post by Mark » Mon Nov 09, 2015 4:22 pm

You can use Ctrl+A to select all the files and drag all of them to the arduino as the link here shows:
http://www.geeetech.com/forum/viewtopic ... 20&t=16433

rmrodrigues
Posts: 36
Joined: Wed Oct 14, 2015 5:37 am

Re: firmware for geeeteh 3D printers

Post by rmrodrigues » Fri Nov 13, 2015 8:08 am

Hi,
How I know that a new version of firmware is available?
Cheers,
RMRodrigues

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: firmware for geeeteh 3D printers

Post by Mark » Fri Nov 13, 2015 4:21 pm

We'll keep all of them updated, and if a new version is available we'll let you know too, tks!

mava70
Posts: 20
Joined: Sun Nov 01, 2015 8:20 am

Re: firmware for geeeteh 3D printers

Post by mava70 » Tue Nov 17, 2015 9:29 pm

Hello,

is it possibile to update Marlin firmware downloading it from github and allineate config.h from your config and new Marlin firmware? Did you do some kind of code personalization in you firmware outside of config.h?

I am interested in RAMPS version.

Thanks

Marco

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: firmware for geeeteh 3D printers

Post by Mark » Thu Nov 19, 2015 5:43 pm

you can do it as you said but note that the marlin version shoud be the same.

azzraell
Posts: 3
Joined: Tue Dec 01, 2015 5:43 am

Re: firmware for geeeteh 3D printers

Post by azzraell » Tue Dec 01, 2015 5:47 am

Hi, iam very new at 3d printing, do i have to download the Ramps file and the Marlin file? or which one do i need? I have the Prusa I3 pro B, and the board is the GT2560, but iam kind of lost, not sure what to do. thanks for the help!

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: firmware for geeeteh 3D printers

Post by Mark » Tue Dec 01, 2015 11:28 am

your printer is I3 pro B with GT2560, then just download this one:
QQ截图20151201112650.jpg
QQ截图20151201112650.jpg (89.21 KiB) Viewed 166821 times

azzraell
Posts: 3
Joined: Tue Dec 01, 2015 5:43 am

Re: firmware for geeeteh 3D printers

Post by azzraell » Tue Dec 01, 2015 11:47 am

Thanks alot, i have a new problem now, the printer wont home on Y axis, it does ok in the x and z axis, but wont work on the Y, any ideas why wont work? what can i do? thanks!

Post Reply

Who is online

Users browsing this forum: No registered users and 6 guests