Check the post please, perhaps your crystal oscillator is not soldered well, or there's a poor contact somewhere:
http://www.geeetech.com/forum/viewtopic ... 20&t=17102
Search found 116 matches
- Sat Jun 25, 2016 9:44 am
- Forum: Control Board
- Topic: Has my Control board died?
- Replies: 18
- Views: 35687
- Sat Jun 25, 2016 9:39 am
- Forum: Others
- Topic: Please help "Error maxtemp"
- Replies: 3
- Views: 7126
Re: Please help "Error maxtemp"
Maybe the max temp in firmware is a little low, so when you set the heat temperature at a high value, it will reach the max temp easily and get the error.
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
- Sat Jun 25, 2016 9:28 am
- Forum: Firmware
- Topic: Marlin Issue
- Replies: 2
- Views: 5004
Re: Marlin Issue
Have you clicked "store memory" after you change it?
- Sat Jun 25, 2016 9:16 am
- Forum: Print Quality
- Topic: Vibrating Y axis
- Replies: 2
- Views: 6545
Re: Vibrating Y axis
What's your printer model? The vibration may be because the belt is too loose, or there's something wrong with the wheel or the bearing?
- Fri Jun 24, 2016 9:09 am
- Forum: Control Board
- Topic: Has my Control board died?
- Replies: 18
- Views: 35687
Re: Has my Control board died?
What's the version of arduino do you use, how about using v1.01?
- Fri Jun 24, 2016 8:57 am
- Forum: Control Board
- Topic: control board problem
- Replies: 11
- Views: 15975
Re: control board problem
Please check the subdivision of the motor:
http://www.geeetech.com/forum/viewtopic ... 17&t=17038
http://www.geeetech.com/forum/viewtopic ... 17&t=17038
- Fri Jun 24, 2016 8:42 am
- Forum: Others
- Topic: curved movement
- Replies: 2
- Views: 4282
Re: curved movement
"the plate is a bowl shape",do you have something to measure it? If it's indeed bent, I think geeetech will replace it for you.
- Thu Jun 23, 2016 6:00 pm
- Forum: LCD Panel
- Topic: Confused between different LCD2004 models
- Replies: 12
- Views: 49730
Re: Confused between different LCD2004 models
You are right, the LCD you bought is not compatible with your board, so it's necessary to figure out the the version of the LCD, as far as I know, white PCB and blue PCB is campatible with GT2560 board.
- Thu Jun 23, 2016 10:14 am
- Forum: LCD Panel
- Topic: Confused between different LCD2004 models
- Replies: 12
- Views: 49730
Re: Confused between different LCD2004 models
Normally LCD 2004 is indeed compatible with GT2560, how do you connect the LCD with your board, can you post a picture?
- Thu Jun 23, 2016 10:01 am
- Forum: Others
- Topic: About the fan extruder, always on?
- Replies: 5
- Views: 8014
Re: About the fan extruder, always on?
It's quite normal, the fans will be always on until you power off the printer.