Search found 116 matches
- Wed Sep 28, 2016 1:35 pm
- Forum: Extruder
- Topic: Solutions for GT2560 extruder not working
- Replies: 40
- Views: 130470
Re: Solutions for GT2560 extruder not working
You can try the installer version of 1.05,see if it works.
- Wed Sep 28, 2016 11:53 am
- Forum: Extruder
- Topic: Another problem with extruder feeding thread
- Replies: 12
- Views: 19313
Re: Another problem with extruder feeding thread
Maybe the driver is overheated? Please make sure the driver is cooled well.
You can also disassemble the feeder to see if there's anything wrong:
http://www.geeetech.com/Documents/MK8%2 ... uction.pdf
You can also disassemble the feeder to see if there's anything wrong:
http://www.geeetech.com/Documents/MK8%2 ... uction.pdf
- Wed Sep 28, 2016 11:50 am
- Forum: Firmware
- Topic: How to upload firmware for GTM32 Pro board?
- Replies: 62
- Views: 244029
Re: The Restock 301(STM32 Pro Board) Firmware Burning Steps
Hi,
It's not easy to flash the firmware in linux, you'll need something linke J-link, minicom, and we haven't tried that yet.
You'd better use a windows system to do that.
It's not easy to flash the firmware in linux, you'll need something linke J-link, minicom, and we haven't tried that yet.
You'd better use a windows system to do that.
- Wed Sep 28, 2016 11:08 am
- Forum: Extruder
- Topic: Another problem with extruder feeding thread
- Replies: 12
- Views: 19313
Re: Another problem with extruder feeding thread
Hi Fernando, Seems the extruder doesn't have enough power to push the filament during printing. You can try to incease the driver voltage, or swap the driver of extruder with other axis, see if it will make any difference. Refer to this link to adjust the voltage: http://www.geeetech.com/forum/viewt...
- Wed Sep 28, 2016 11:00 am
- Forum: Extruder
- Topic: Extruder not working
- Replies: 124
- Views: 326848
Re: Extruder not working
The extruder problem might be because the driver of extruder is overheated, you need make sure the driver is cooled well, or you can swap the driver of extruder with other axis.
- Wed Sep 28, 2016 10:26 am
- Forum: Firmware
- Topic: Cant upload my firmware
- Replies: 11
- Views: 16737
Re: Cant upload my firmware
There's difference setting for 12864 and 2004 in firmware,
Refer to this link:
http://www.geeetech.com/forum/viewtopic ... 23&t=17040
Refer to this link:
http://www.geeetech.com/forum/viewtopic ... 23&t=17040
- Wed Sep 28, 2016 10:20 am
- Forum: Stepper Motor
- Topic: x/y axis ribbing - corrugated print
- Replies: 2
- Views: 5711
Re: x/y axis ribbing - corrugated print
The picture failed for some reason, can you post it again?
- Wed Sep 28, 2016 10:12 am
- Forum: Firmware
- Topic: Flip uploading
- Replies: 3
- Views: 5378
Re: Flip uploading
Hi Rob,
There are the instructions to install the driver in this path:
Atmel\Flip 3.4.7\usb\UpdateDriver\w2k You can update the driver according to the info there.
There are the instructions to install the driver in this path:
Atmel\Flip 3.4.7\usb\UpdateDriver\w2k You can update the driver according to the info there.
- Sat Sep 03, 2016 9:47 am
- Forum: Products FAQ
- Topic: x axis problem
- Replies: 7
- Views: 9725
Re: x axis problem
Perhaps the crystal oscillator doesn't work on the board, you can check the voltage of the two pins to GND, normally they should be both be about 2V, the difference of the two voltage is about 0.2V
- Sat Sep 03, 2016 9:18 am
- Forum: Products FAQ
- Topic: Problem with Extruder of M201
- Replies: 3
- Views: 6564
Re: Problem with Extruder of M201
Could it extrudes normally when you manually push the filament with hand?
If not, then it might be the hotend getting clogged, you can try to clean block and the nozzle, see if it helps;
If not, then it might be the hotend getting clogged, you can try to clean block and the nozzle, see if it helps;