Search found 49 matches

by Ricky1966
Tue Feb 19, 2019 6:03 pm
Forum: Geeetech A10 Series
Topic: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli
Replies: 33
Views: 63747

Re: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli

@vert

Hi, great jobs (1.1.9 and 2.0) but I've just a little question. I've read somewhere ther is a problem with the extruder fav speed, did you solved?
by Ricky1966
Thu Feb 14, 2019 3:20 pm
Forum: Geeetech A10 Series
Topic: Tricolor Hotend
Replies: 25
Views: 4729

Re: Tricolor Hotend

@ _kaktus_ Tks for your answer. Maybe next time is better I'm look the board before ask :D As I'm away from home, the board have just a third driver for E2 motor or I need to buy it? Do you think is possible to customize A10 or A10M with tri channel hotend? Which changeing is needed for the hotend a...
by Ricky1966
Fri Feb 08, 2019 6:19 pm
Forum: Geeetech A10 Series
Topic: Tricolor Hotend
Replies: 25
Views: 4729

Re: Tricolor Hotend

Tks Wingding5. I'm looking for update my A10. The board is 2560 vers. 3. I think ther isn't third slot for extruder, so probably isn't possible to do a RGB hotend. I've also thinking to do a differtly approce; if is possible, to take the pins of one of the two extruders slots, and use it with shift ...
by Ricky1966
Thu Feb 07, 2019 11:37 pm
Forum: Geeetech A10 Series
Topic: Tricolor Hotend
Replies: 25
Views: 4729

Tricolor Hotend

Hi everybody. Someone knows if is possible to adapt this hotend on a A10?
https://www.ebay.co.uk/itm/2018-New-Thr ... 2886394014
by Ricky1966
Thu Feb 07, 2019 2:05 am
Forum: Geeetech A10 Series
Topic: a10m upgrade with MK8 Extruder Aluminum feeder Kit
Replies: 1
Views: 1272

Re: a10m upgrade with MK8 Extruder Aluminum feeder Kit

Hi, maybe you have mounted reversed, no problem, have you just flashed firmware? If yes, you should to change clockwise, anticlockwise rotetion of extruder in configure.h.
by Ricky1966
Fri Feb 01, 2019 12:37 am
Forum: Geeetech A10 Series
Topic: A10M Extruder step/mm calibration
Replies: 7
Views: 12533

Re: A10M Extruder step/mm calibration

Tks! I'll try in two hours
by Ricky1966
Wed Jan 30, 2019 10:23 pm
Forum: Geeetech A10 Series
Topic: A10M Extruder step/mm calibration
Replies: 7
Views: 12533

A10M Extruder step/mm calibration

Hi everybody. I know, with Repetier Host, I could extrude 100 mm of filament with line gcode :
G1 E100 F200;
This comand is right for A10, with one feeder extruder, but how can extrude 100 mm of filament from both extruders on A10M?
Tks
by Ricky1966
Wed Jan 16, 2019 7:08 pm
Forum: Geeetech A10 Series
Topic: A10 Capacitive Bed Levelling Sensor
Replies: 8
Views: 4803

Re: A10 Capacitive Bed Levelling Sensor

Hi. I'm very intresting about the implememtation of this sensos, for this, I've some quesrions :
- have you done it?
- which firmware in your printer?
- if you have mounted the support above linked, have you modify the xy of the level points?
Tks for news :D
by Ricky1966
Tue Jan 15, 2019 5:27 am
Forum: Geeetech A10 Series
Topic: A10, Marlin 2.0 beta and 3dtouch
Replies: 2
Views: 4109

Re: A10, Marlin 2.0 beta and 3dtouch

Tks, very clear :D
by Ricky1966
Sat Jan 12, 2019 11:53 pm
Forum: Geeetech A10 Series
Topic: A10, Marlin 2.0 beta and 3dtouch
Replies: 2
Views: 4109

A10, Marlin 2.0 beta and 3dtouch

Someone among you, will be so patient, to teach me how to wire the 3Dtouch sensor, and level the bed, step by step? A10 with Marlin 2.0 Beta. Thank you