Search found 70 matches

by MichaelK
Thu Aug 30, 2018 12:13 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

Change the value and try again..... :roll:

I can't offer a tutorial here to develop with Arduino or Marlin.
Youtube has many videos on it....
by MichaelK
Wed Aug 29, 2018 6:45 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

zonalimitatore wrote:
Wed Aug 29, 2018 6:32 pm
Anyway...i need to rewrite the bootloader using my arduino uno like programmer,right?
It is possible, maybe better using a ATMEGA2560.

https://www.youtube.com/watch?v=2N1zgX8 ... gs=pl%2Cwn
by MichaelK
Wed Aug 29, 2018 5:50 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

I do not know if my connections that I know really fit, but you can write to the support to tell you the connections:
https://www.geeetech.com/technical_support.html
by MichaelK
Wed Aug 29, 2018 2:21 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

You flash the firmware onto your own risk! I mention that everywhere! Disconnecting every machine during flashing can damage the bootloader! First, don't install the version with bootloader included. The bootloader already installed. Look here to load and use the original firmware: http://www.geeete...
by MichaelK
Wed Aug 29, 2018 12:51 am
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

Perfect.Tonight i try to flash ;) Thanks :mrgreen: Into the menu you found the new setting "manual leveling" To use them klick the wheel down and start the leveling. The A10 now drives 9 points on the heating bed, starting with point 1. Put a piece of paper under the nozzle and turn the wheel up an...
by MichaelK
Tue Aug 28, 2018 7:02 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

Yes, the configuration is set.

Now you need to leveling your heatbed very precision! After leveling you could print.
by MichaelK
Tue Aug 28, 2018 12:39 pm
Forum: Geeetech A30 Series
Topic: Adding another extruder for multi material prints
Replies: 2
Views: 1321

Re: Adding another extruder for multi material prints

What should be the result?
Multicolorprint or print two workpieces at the same time??? :?:

Multicolor: you need to make your own firmware. With A30 it's not easy because the A30 using a 32-bit Controller.
To print multicolor it's better and easier to by the new Geeetech A10M!
by MichaelK
Tue Aug 28, 2018 12:32 pm
Forum: Geeetech A30 Series
Topic: my nozzle has to rub the Geeetech superplate
Replies: 6
Views: 2323

Re: my nozzle has to rub the Geeetech superplate

:shock:
if the bed is well leveld then the nozzle should not touch the bed without filament.
try to keep the printouts out.

You can move the prints in your own slicer to other positions out of the middle.
by MichaelK
Tue Aug 28, 2018 12:19 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 firmware Marlin 1.1.9
Replies: 86
Views: 47476

Re: Geeetech A10 firmware Marlin 1.1.9

Hello everyone... This firm it's ready for install o i need edit config in arduino ide? Or simply click on marlin.ino and upload on board? If you need to change any functions into Marlin you need to use the arduino ide to do it. You can use many ways to install the firmware. two possebilities: 1: A...
by MichaelK
Tue Aug 28, 2018 1:16 am
Forum: Software
Topic: I am having problems getting config setting to apply correctly....I think this is the correct place to post this...
Replies: 8
Views: 5171

Re: I am having problems getting config setting to apply correctly....I think this is the correct place to post this...

It's difficult! Install cura and select "anycubic i3 Mega" als default Printer from the list of custom printers After that you need to setup the dimensions of the printer manually, because the i3Mega use the dimensions: 210x210x205 (long, width,height) The A30 is bigger. After that you need to level...