Search found 48 matches

by 3dtech
Mon Jun 05, 2017 6:09 pm
Forum: Print Quality
Topic: Is it more feasible to print jewelry on a 3D printer or to m
Replies: 0
Views: 1749

Is it more feasible to print jewelry on a 3D printer or to m

It depends on the type of jewelry and the type of printer. High quality printing in metals requires relatively expensive equipment to get good results. Even with good equipment, you'd still have manual mounting, fit and finish work. 3d printed castable Jewelry surat -sla technology However, relative...
by 3dtech
Sat Jun 03, 2017 8:03 pm
Forum: Print Quality
Topic: Weird Quality Issue
Replies: 9
Views: 4491

Re: Weird Quality Issue

I'll definitely give this a try; the intent of course being to slow down the printer during infill and such. The latest version of Cura gives you the option to copy the settings when you switch over from "quickprint" to "full settings". When I do this, the infill speed for example is set as 80mm/s. ...
by 3dtech
Fri Jun 02, 2017 6:10 pm
Forum: Open Hardware
Topic: iduino yun shield UART not working
Replies: 8
Views: 8891

Re: iduino yun shield UART not working

Uno can not support some codes of bridge.
Please Try ConsoleASCII.
by 3dtech
Wed May 31, 2017 8:21 pm
Forum: Geeetech Delta Series
Topic: Mac Version of Repetier-Host with M301
Replies: 4
Views: 3299

Re: Mac Version of Repetier-Host with M301

The next decision is, how to send data to the firmware. The method that was planned with the first firmwares works like ping-pong. The host send a command and waits for the firmware to return an ok. This causes latencies, which can result in empty buffers if you have many small moves. To improve spe...
by 3dtech
Wed May 31, 2017 8:21 pm
Forum: Geeetech Delta Series
Topic: Mac Version of Repetier-Host with M301
Replies: 4
Views: 3299

Re: Mac Version of Repetier-Host with M301

The next decision is, how to send data to the firmware. The method that was planned with the first firmwares works like ping-pong. The host send a command and waits for the firmware to return an ok. This causes latencies, which can result in empty buffers if you have many small moves. To improve spe...
by 3dtech
Tue May 30, 2017 5:47 pm
Forum: Print Quality
Topic: At what stage of jewelry manufacturing is 3D printing used?
Replies: 0
Views: 1526

At what stage of jewelry manufacturing is 3D printing used?

This is an excellent question. The answer to this is going to be pretty long. So kindly bear with me. The thing you have to know about conventional jewelry manufacturing is most often, the jewelry is made by using a process called investment casting or lost-wax casting. Recommend reading this articl...
by 3dtech
Thu May 18, 2017 6:14 pm
Forum: Print Quality
Topic: Prusa I3 pro B : Need some advices for quality printing
Replies: 9
Views: 10431

Re: Prusa I3 pro B : Need some advices for quality printing

la or abs or other quality,,low,normal,high solid, dense,hollow,etc i do a plate adhesion also,it automatically slices it while you choose,no key for it. when bottom right corner of cura screen says send to SD,just click it, it will send it to SD card. then shut down cura and start repetier. Or pull...
by 3dtech
Thu May 11, 2017 7:52 pm
Forum: Hot bed
Topic: mk2a heatbed upgrade to mk3 heat bed ?
Replies: 5
Views: 5199

Re: mk2a heatbed upgrade to mk3 heat bed ?

You could always spray paint the red hot bed black with some exhaust paint, I personally like the red. If you are 'upgrading' because the red stock hot bed doesn't heat fast enough, that's because the power supply voltage is set too low. You can crank up the supply voltage on the stock power supply ...
by 3dtech
Fri Apr 28, 2017 8:56 pm
Forum: Control Board
Topic: 3D touch GT2560
Replies: 9
Views: 7064

Re: 3D touch GT2560

I have the 3D touch leveling sensors. I have the GT2560 board but not like in the description. So now i dont know how to wire the sensors. I cant solder the 3 pins on ZMAX because there are only 2. How can i wire the sensors on the board? Show attachement, this are my endstops on the board.
by 3dtech
Tue Apr 25, 2017 8:58 pm
Forum: Assembly
Topic: Delta Rostock mini G2s pro-> Diagonal Push Rod broken
Replies: 8
Views: 4283

Re: Delta Rostock mini G2s pro-> Diagonal Push Rod broken

I tried contacting the sales service(as you said I should)...the first time my E-Mail programm somehow didin't send the mail(as I found out a month or so later), tried again aaaand I got in contact with a really nice guy from geetech sale support. Told and explained him my Problems and just 1-2 week...