Search found 362 matches

by Sherry
Fri Jul 31, 2015 3:31 pm
Forum: Others
Topic: Actual maximum print size?
Replies: 6
Views: 4871

Re: Actual maximum print size?

Hi, I had a similar problem, I'm not sure it's the same one though. My print-surface was also smaller than advertised, the issue was the washers used to keep the rods in place. They impede full movements. Video to show the problem: https://onedrive.live.com/redir?resid=D27D44560BF591CC!19046&authke...
by Sherry
Fri Jul 31, 2015 3:11 pm
Forum: Firmware
Topic: Mini G2 Firmware values
Replies: 7
Views: 5539

Re: Mini G2 Firmware values

I am in Arduino 1.6.5 and want to compile. Are there settings in file configuration.h that I must change before compiling? I cannot find these settings - initial z axis height, final Z axis height,Z_PROBE_OFFSET. What part of the file are they in? I looked at your reference and these measurements a...
by Sherry
Fri Jul 31, 2015 2:59 pm
Forum: Firmware
Topic: Need origional firmware
Replies: 2
Views: 2153

Re: Need origional firmware

gamma1148 wrote:Hello
I purchased Acrylic Frame Prusa Mendel I3 unassembled DIY kit GT2560 MK8 Reprap 3D Printer
I wiped out the stock firmware and I need a new copy. can you please email me?
Thank you!!!
Mike
hi,i've send it to your mailbox. :D
by Sherry
Fri Jul 31, 2015 2:54 pm
Forum: Firmware
Topic: Need origional firmware
Replies: 2
Views: 2153

Re: Need origional firmware

gamma1148 wrote:Hello
I purchased Acrylic Frame Prusa Mendel I3 unassembled DIY kit GT2560 MK8 Reprap 3D Printer
I wiped out the stock firmware and I need a new copy. can you please email me?
Thank you!!!
Mike
hi,what's you mainboard type?
by Sherry
Fri Jul 31, 2015 2:51 pm
Forum: Firmware
Topic: Acrylic Frame Prusa Mendel I3 unassembled DIY kit GT2560 MK8
Replies: 4
Views: 3184

Re: Acrylic Frame Prusa Mendel I3 unassembled DIY kit GT2560

hi,sanguinololu is the stand configration of Prusa Mendel I3(iteration 3),if you would like to connect it to GT2560,you can have a try,and i will provide the firmware for you.
by Sherry
Fri Jul 31, 2015 2:24 pm
Forum: Firmware
Topic: Delta g2 firmware compiling
Replies: 8
Views: 5373

Re: Delta g2 firmware compiling

hi,what's version of Arduino you use now?you can install a lower version to compile the firmware.
here is the download link: http://www.geeetech.com/wiki/index.php/Download
by Sherry
Fri Jul 31, 2015 11:43 am
Forum: Others
Topic: Actual maximum print size?
Replies: 6
Views: 4871

Re: Actual maximum print size?

hi,johnp,sorry for my presentation mistake ,i mean i will modify the parameter in wiki . the real specification is :Print Volume: cylindrical,D:190mm,H:200mm. please look at the pictures.in my repetier host,i can move x to -90. and in the firmware DELTA_PRINTABLE_RADIUS is defined as 90 ,it was to p...
by Sherry
Fri Jul 31, 2015 9:48 am
Forum: Firmware
Topic: Mini G2 Firmware values
Replies: 7
Views: 5539

Re: Mini G2 Firmware values

I have assembled Mini G2. With firmware loaded in Arduino instructions say "Find the value you need to comlile according to your printer" I changed com port but I do not know what other values I need. Where do I get them? hi,you need to modify those values:initial z axis height, final Z axis height...
by Sherry
Fri Jul 31, 2015 9:04 am
Forum: Extruder
Topic: motors extruder not working
Replies: 6
Views: 5420

Re: motors extruder not working

do you set up feet rate?Normally,the feed rate is 100.
by Sherry
Thu Jul 30, 2015 5:52 pm
Forum: Others
Topic: End stop problem Prusa I3 pro B + GT2560
Replies: 3
Views: 5481

Re: End stop problem Prusa I3 pro B + GT2560

Anehall wrote:No only x and y axiz homes... z axis goes upwards instead of down... The same if i disconect the End stop for z axis.
hi,you can check whether endstop wire of z axis is bad.