if your cpmputer could not detect the usb device automatically,please install the usb driver manually.This is the link for intall the driver manually.
http://www.geeetech.com/forum/viewtopic ... 508#p25508
Search found 362 matches
- Wed Jul 08, 2015 2:12 pm
- Forum: Control Board
- Topic: gt2560 on usb
- Replies: 22
- Views: 20748
- Wed Jul 08, 2015 2:01 pm
- Forum: Others
- Topic: Problems on my geeetech i3B
- Replies: 6
- Views: 5112
Re: Problems on my geeetech i3B
hi,you connect the endstop wire to wrong slot,the wire should connect to "sig" and "-".please see the picture where i mark a red circle.
- Wed Jul 08, 2015 11:44 am
- Forum: Extruder
- Topic: How to improve the surface condition of the print?
- Replies: 2
- Views: 2993
- Wed Jul 08, 2015 11:41 am
- Forum: Extruder
- Topic: How to improve the surface condition of the print?
- Replies: 2
- Views: 2993
Re: How to improve the surface condition of the print?
hi,please do the following steps.
1.Tight coupling shown in the picture.
2.the hot bed is out of level,please do the auto leveling .
1.Tight coupling shown in the picture.
2.the hot bed is out of level,please do the auto leveling .
- Wed Jul 08, 2015 10:51 am
- Forum: Stepper Motor
- Topic: Motors moving only to home
- Replies: 3
- Views: 2944
Re: Motors moving only to home
hi,do LCD panel display any error such as MINTEMP error or MAXTEMP error?please do the following steps.
1.Click "emergency stop" in the repetier-host.
2.Reconnect the wire to controlboard.please plug the wire to into the slot firmly.
3.Restart the printer.
1.Click "emergency stop" in the repetier-host.
2.Reconnect the wire to controlboard.please plug the wire to into the slot firmly.
3.Restart the printer.
- Wed Jul 08, 2015 9:17 am
- Forum: Extruder
- Topic: Extruder and Bed temprature
- Replies: 1
- Views: 2362
Re: Extruder and Bed temprature
here are some ways to troubleshoot the problem. 1.Pulling out the thermistor wire and using a multimeter to measure resistance of thermistors,the value should be 0; 2.Connecting the thermistor slots with Jumper Caps,check the resistance of thermistors,the value should be 385; 3.without heating,pleas...
- Wed Jul 08, 2015 8:43 am
- Forum: Control Board
- Topic: mintemp Rostock G2 control board
- Replies: 6
- Views: 5708
Re: mintemp Rostock G2 control board
Please reburn the firmware.Then take a picture of what LCD show.
- Tue Jul 07, 2015 4:24 pm
- Forum: Stepper Motor
- Topic: Z-Axis homes above the extruder
- Replies: 3
- Views: 3586
Re: Z-Axis homes above the extruder
hi.the reason is that the screw impact the z-endstop is not long enough.please tighten down the screw to make it impact the z-endstop ealier.
- Tue Jul 07, 2015 3:18 pm
- Forum: Control Board
- Topic: Controller Board and LCD issues
- Replies: 7
- Views: 5148
Re: Controller Board and LCD issues
hi,please upload photos of the print board you have mounted.let me check the wire connection.photos should be clear as far as possible.thx.
- Tue Jul 07, 2015 2:28 pm
- Forum: Control Board
- Topic: Controller Board and LCD issues
- Replies: 7
- Views: 5148
Re: Controller Board and LCD issues
Please set the hotbed temperature to 60°,you can modify the temperature of hotbed manually with LCD panel.
link:http://www.geeetech.com/wiki/index.php/ ... nstruction
link:http://www.geeetech.com/wiki/index.php/ ... nstruction