just take modified firmware by vert
put the right config... h file for your printer into the marlin directory before flashing
and enjoy
good work vert
Search found 25 matches
- Wed Mar 13, 2019 10:46 pm
- Forum: Geeetech A10 Series
- Topic: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli
- Replies: 33
- Views: 137551
- Thu Mar 07, 2019 3:45 pm
- Forum: Geeetech A10 Series
- Topic: A10M keeps dying mid print!
- Replies: 12
- Views: 15126
Re: A10M keeps dying mid print!
seems to be normal that the a10 die after some month
stupid me i have ordered an A20 for replacement of my defect A10
but that can go wrong too
stupid me i have ordered an A20 for replacement of my defect A10
but that can go wrong too
- Thu Mar 07, 2019 3:25 pm
- Forum: Geeetech A10 Series
- Topic: Is there a good replacement for the GT2560 rev B?
- Replies: 8
- Views: 9275
Re: Is there a good replacement for the GT2560 rev B?
@ William can you give me a link or contact for the sales support? my thermistor cables from bed are placed in the middle of the soldered connectors i have problem at two places there is a wrong temp reading at both thermistors shown on lcd both around 125 degree Celsius i checked thermistor both ar...
- Wed Mar 06, 2019 1:00 am
- Forum: Geeetech A10 Series
- Topic: Is there a good replacement for the GT2560 rev B?
- Replies: 8
- Views: 9275
Re: Is there a good replacement for the GT2560 rev B?
in this case, if we have same problems with several boards it must be a trivial problem i checked my sensors and all sensors are good after flashing latest firmware i have also set the sensor in the code (configuration.h file) search for sensor type 3950 and in the code you will find the subscriptio...
- Tue Mar 05, 2019 6:31 pm
- Forum: Geeetech A10 Series
- Topic: Is there a good replacement for the GT2560 rev B?
- Replies: 8
- Views: 9275
Re: Is there a good replacement for the GT2560 rev B?
i have same problem with mine a10 printer, several replacement boards do not work (temperature failure) i spent more money for replacement parts the last month as i paid for whole printer when it comes new @william is it possible to work with adapters or is there any kind of upgrade kit REV B board ...
- Tue Mar 05, 2019 6:22 pm
- Forum: Geeetech A10 Series
- Topic: A10 - GT2560 V3 (!) - no PWM - 24V steady full power
- Replies: 7
- Views: 10114
Re: A10 - GT2560 V3 (!) - no PWM - 24V steady full power
Hi Stefan, next days i get an A20 with rev3 Board, i am also interested whre to find the right connections. Did you find a jumper or so? Otherwise try the Marlin 2.0.xx firmware from Vertabreaker here in Forum. You can do most settings by this firmware on lcd. As i remind from my older A10 and Rev B...
- Mon Mar 04, 2019 7:28 pm
- Forum: Geeetech A10 Series
- Topic: Is My A10m Board Fried??
- Replies: 18
- Views: 20685
Re: Is My A10m Board Fried??
btw the Rev B board seems to be a bad thing, a wide variety from good and working till broken i compared my pre installed gt2650 Rev B with the current replacement board bot have difference, where through hole vias are filled with solder tin or not or if board ist cleaned up with alcohol or another ...
- Mon Mar 04, 2019 7:18 pm
- Forum: Geeetech A10 Series
- Topic: Is My A10m Board Fried??
- Replies: 18
- Views: 20685
Re: Is My A10m Board Fried??
i found the mistake I have shortings over my pullup resistor system for Heat Sensors. measuring form sensors connecting pins onboard R4 and R58 give wrong values from my old board i can measure direct from onboard connectiong pin of sensor to R4 and R58 4,7K Ohm my actual board give from pin to R4 2...
- Mon Mar 04, 2019 3:37 pm
- Forum: Control Board
- Topic: Schematic for GT2560 Rev B?
- Replies: 6
- Views: 14964
- Mon Mar 04, 2019 3:29 pm
- Forum: Control Board
- Topic: Schematic for GT2560 Rev B?
- Replies: 6
- Views: 14964
Re: Schematic for GT2560 Rev B?
Hello, i need Rev. B Schematic. I have shortings over my pullup resistor system for Heat Sensors. measuring form sensors connecting pins onboard R4 and R58 give wrong values from my old board i can measure direct from onboard connectiong pin of sensor to R4 and R58 4,7K Ohm my actual board give from...