Search found 25 matches

by bernte_one
Wed Mar 13, 2019 10:46 pm
Forum: Geeetech A10 Series
Topic: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli
Replies: 37
Views: 32583

Re: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli

:roll: just take modified firmware by vert

put the right config... h file for your printer into the marlin directory before flashing

and enjoy

good work vert
by bernte_one
Thu Mar 07, 2019 3:45 pm
Forum: Geeetech A10 Series
Topic: A10M keeps dying mid print!
Replies: 13
Views: 1597

Re: A10M keeps dying mid print!

seems to be normal that the a10 die after some month :x

stupid me i have ordered an A20 for replacement of my defect A10
but that can go wrong too
by bernte_one
Thu Mar 07, 2019 3:25 pm
Forum: Geeetech A10 Series
Topic: Is there a good replacement for the GT2560 rev B?
Replies: 9
Views: 1261

Re: Is there a good replacement for the GT2560 rev B?

@ William can you give me a link or contact for the sales support? my thermistor cables from bed are placed in the middle of the soldered connectors i have problem at two places there is a wrong temp reading at both thermistors shown on lcd both around 125 degree Celsius i checked thermistor both ar...
by bernte_one
Wed Mar 06, 2019 1:00 am
Forum: Geeetech A10 Series
Topic: Is there a good replacement for the GT2560 rev B?
Replies: 9
Views: 1261

Re: Is there a good replacement for the GT2560 rev B?

in this case, if we have same problems with several boards it must be a trivial problem i checked my sensors and all sensors are good after flashing latest firmware i have also set the sensor in the code (configuration.h file) search for sensor type 3950 and in the code you will find the subscriptio...
by bernte_one
Tue Mar 05, 2019 6:31 pm
Forum: Geeetech A10 Series
Topic: Is there a good replacement for the GT2560 rev B?
Replies: 9
Views: 1261

Re: Is there a good replacement for the GT2560 rev B?

i have same problem with mine a10 printer, several replacement boards do not work (temperature failure) i spent more money for replacement parts the last month as i paid for whole printer when it comes new @william is it possible to work with adapters or is there any kind of upgrade kit REV B board ...
by bernte_one
Tue Mar 05, 2019 6:22 pm
Forum: Geeetech A10 Series
Topic: A10 - GT2560 V3 (!) - no PWM - 24V steady full power
Replies: 8
Views: 1376

Re: A10 - GT2560 V3 (!) - no PWM - 24V steady full power

Hi Stefan, next days i get an A20 with rev3 Board, i am also interested whre to find the right connections. Did you find a jumper or so? Otherwise try the Marlin 2.0.xx firmware from Vertabreaker here in Forum. You can do most settings by this firmware on lcd. As i remind from my older A10 and Rev B...
by bernte_one
Mon Mar 04, 2019 7:28 pm
Forum: Geeetech A10 Series
Topic: Is My A10m Board Fried??
Replies: 21
Views: 2412

Re: Is My A10m Board Fried??

btw the Rev B board seems to be a bad thing, a wide variety from good and working till broken i compared my pre installed gt2650 Rev B with the current replacement board bot have difference, where through hole vias are filled with solder tin or not or if board ist cleaned up with alcohol or another ...
by bernte_one
Mon Mar 04, 2019 7:18 pm
Forum: Geeetech A10 Series
Topic: Is My A10m Board Fried??
Replies: 21
Views: 2412

Re: Is My A10m Board Fried??

i found the mistake I have shortings over my pullup resistor system for Heat Sensors. measuring form sensors connecting pins onboard R4 and R58 give wrong values from my old board i can measure direct from onboard connectiong pin of sensor to R4 and R58 4,7K Ohm my actual board give from pin to R4 2...
by bernte_one
Mon Mar 04, 2019 3:29 pm
Forum: Control Board
Topic: Schematic for GT2560 Rev B?
Replies: 6
Views: 7285

Re: Schematic for GT2560 Rev B?

Hello, i need Rev. B Schematic. I have shortings over my pullup resistor system for Heat Sensors. measuring form sensors connecting pins onboard R4 and R58 give wrong values from my old board i can measure direct from onboard connectiong pin of sensor to R4 and R58 4,7K Ohm my actual board give from...