Search found 18 matches

by Kibo
Tue Oct 27, 2020 2:15 am
Forum: Geeetech I3 Pro W
Topic: Changing heatbed dimensions
Replies: 1
Views: 1814

Changing heatbed dimensions

Hey everyone, I modified my printer and upgraded to a bigger heatbed. However, the maximum dimensions of the heatbed seem to be set in the firmware of the printer: It is not possible to move out of the original dimensions of the heatbed. The printer just stops. Regards manual control and generated g...
by Kibo
Sat Jul 27, 2019 6:38 pm
Forum: Software
Topic: Easyprint 1.2.6 new bug discovered
Replies: 14
Views: 11111

Re: Easyprint 1.2.6 new bug discovered

Hi, but in fact, the support is to protect your dangling parts, so you don't need to adjust the values very much. So are you saying: "Yes, there is a bug in the software, I was wrong to doubt you. The software is not working as intended, but I don´t care, because I tell you, that you do not need th...
by Kibo
Thu Jul 25, 2019 3:38 am
Forum: Software
Topic: Easyprint 1.2.6 new bug discovered
Replies: 14
Views: 11111

Re: Easyprint 1.2.6 new bug discovered

I just read a good tutorial on how to improve the print quality when using support. There they experimented with different Z distances. I would very much appreciate it, if this feature was added in a future version of easyprint.
by Kibo
Wed Jul 24, 2019 4:37 am
Forum: Software
Topic: Easyprint 1.2.6 new bug discovered
Replies: 14
Views: 11111

Re: Easyprint 1.2.6 new bug discovered

OH, you can observe the distance transform I set However, we set up support to ensure that the suspended parts do not fall. So can't be set too big. Yes, I can confirm that there is a difference between values <1 mm and >1 mm but there is no difference between values <1 mm. So let´s say 0,1 mm isn´...
by Kibo
Wed Jul 24, 2019 4:35 am
Forum: Software
Topic: Easyprint 1.2.6 new bug discovered
Replies: 14
Views: 11111

Re: Easyprint 1.2.6 new bug discovered

Yes, you can set the value but it does not have any effect on the model. I also enabled support interface. I don´t know if this has any influence on it. I took a few screenshots. Here I set the Z-distance to 1 mm. The gap is clearly visible: Z distance 1 mm.JPG Here I set the Z-distance to 0,9 mm. T...
by Kibo
Tue Jul 23, 2019 2:05 am
Forum: Software
Topic: Easyprint 1.2.6 new bug discovered
Replies: 14
Views: 11111

Easyprint 1.2.6 new bug discovered

Hallo there, I am currently experimenting with different support settings. There I noticed a bug (I think): Eaysyprint 1.2.6 --> Slicing Settings --> Parameters (---> enable support) --> Z distance: This parameter seems to define the distance between the actual print and the support. The default set...
by Kibo
Mon Aug 06, 2018 8:40 pm
Forum: Bug report
Topic: So many friggin bugs!
Replies: 5
Views: 15757

Re: So many friggin bugs!

sean wrote:
Tue Jul 17, 2018 11:38 am
@Kibo
Low current will activate power-off detection module and then restart your machine.
You can replace capacity by ultracapacitor and remove the detection module.
How could a low current occur?
by Kibo
Mon Aug 06, 2018 8:39 pm
Forum: Bug report
Topic: So many friggin bugs!
Replies: 5
Views: 15757

Re: So many friggin bugs!

Hi, Kibo. Q1: changing wall thickness... it works wrong. A1: I saw your attachment and felt confused. The parameters shouldn't be like that. Have you ever installed an old version of EP and did not delete old configuration stored in C:\Users\{username}\AppData\roaming\easyprint before using new one...
by Kibo
Mon Aug 06, 2018 8:31 pm
Forum: Software
Topic: Easyprint software for WINDOWS
Replies: 44
Views: 1509154

Re: Easyprint software for WINDOWS

I can confirm that with 1.2.3, the print speed setting is now working. However I am experiencing a major bug: I cannot adjust the filament flow settings. The value is set to 250 % and whatever value I enter, the G-Code does not change. I am currently having constant underextrusion due to the extrude...