Search found 10 matches

by Xaroos
Wed Sep 20, 2017 5:35 pm
Forum: Feedback&Suggestion
Topic: support
Replies: 4
Views: 3030

Re: support

Thanks, now im stuck with the sensor!
by Xaroos
Tue Sep 19, 2017 7:55 pm
Forum: Feedback&Suggestion
Topic: support
Replies: 4
Views: 3030

support

IN the topic you say "Your suggestions or opinions about our service will be much appreciated" You can for one answer people when they send you an email for support. I have been looking to see how mount and install an auto touch to my I3 pro C , emailing support and other people in your company but ...
by Xaroos
Wed Sep 06, 2017 7:25 pm
Forum: Mods And Hacks
Topic: I3 pro C auto level installation
Replies: 1
Views: 1660

I3 pro C auto level installation

Hi
Does anyone have the instruction to mount the auto level to I3 pro C dual extruder
all i find is I3 pro B , and any other info that can help/

thansk
by Xaroos
Sat Aug 12, 2017 6:00 pm
Forum: Project Talent Show
Topic: My I3 Pro C
Replies: 6
Views: 12446

Re: My I3 Pro C

I also had lots of problems with my i3 pro C, But the good thing was that the geeetech people were very helpful to sort them out. As it was mentioned above you need to spend a lots of time to understand your printer and how to use it, Ive spent hours to read about 3d printing and what to do and don'...
by Xaroos
Mon Jul 24, 2017 4:44 pm
Forum: Print Quality
Topic: Quality issues of your printed patrts
Replies: 15
Views: 28120

Re: Quality issues of your printed patrts

its a new printer so i didnt think it needs cleaning ,how do i clean it ,or check the temprature
by Xaroos
Sun Jul 23, 2017 6:07 pm
Forum: Others
Topic: print 2 colour
Replies: 1
Views: 1545

print 2 colour

How do you print from the second extruder?
my first one does not work properly want to check if its the extruder or not?
i get this quality.one is a cube and one is a PEZ ,
by Xaroos
Sat Jul 22, 2017 11:15 am
Forum: Print Quality
Topic: Quality issues of your printed patrts
Replies: 15
Views: 28120

Re: Quality issues of your printed patrts

HI I have a I3 pro C that i havent been able to get any prints from it till now this is mostly what im getting (see images)seems that it does not feed enough material. the bed is set to 60 and the extruder to 200 degrees. the extruder came without one ofthe white tubes that you feed the filemant in ...
by Xaroos
Sun Jul 16, 2017 3:13 pm
Forum: Assembly
Topic: Z axis won’t move on Geeetech Prusa I3 X
Replies: 12
Views: 33468

Re: Z axis won’t move on Geeetech Prusa I3 X

I had the same problem along with lots of other problems! i acualy noticed that the 2 shaft that holds the extruder and X motor were quit tight where it goes to the X motor side, i used the files and losened them a little bit ( becarful not to file too much just take the paint away softly) and used ...
by Xaroos
Mon Jul 10, 2017 3:20 pm
Forum: Assembly
Topic: I3 Pro C
Replies: 4
Views: 2696

Re: I3 Pro C

After going through the whole manual found all the wires but it would have been good to have a sketch of what goes where that the users dont have to waste so much time.
by Xaroos
Sun Jul 09, 2017 8:07 am
Forum: Assembly
Topic: I3 Pro C
Replies: 4
Views: 2696

I3 Pro C

Hi I am assembling my I3 Pro ,in the wiring section it says connect X motor to here Y motor to there but no where it says which one X motor or Y motor, The instruction that comes with it shows a video for assembling a similar printer but not exact like there is no mention of the fan that goes behind...