Search found 42 matches

by raoulito9
Thu Jun 08, 2017 3:44 am
Forum: Firmware
Topic: New 2017 firmware for rostock 301 ?
Replies: 13
Views: 8725

Re: New 2017 firmware for rostock 301 ?

I mean using color mixing ability with gcodes, wich is not possible with actual not open source firmware.
by raoulito9
Wed Jun 07, 2017 3:38 am
Forum: Firmware
Topic: New 2017 firmware for rostock 301 ?
Replies: 13
Views: 8725

New 2017 firmware for rostock 301 ?

Hi. I bough a rostock 301 in september 2016. After modding it , it slowly works. I use firmware 1.02 When will we get a new firmware, - allowing to retract correctly (retracting only one filament is not enough on diamond head, need to retract the 3 of them to avoid a "hairy print") - to exploit real...
by raoulito9
Sun Mar 12, 2017 5:22 pm
Forum: Software
Topic: Rostock 301 Bed Levelling
Replies: 9
Views: 7238

Re: Rostock 301 Bed Levelling

:-)
I'm happy that this is usefull for some people around (Autralia !!!; i'm from Paris France).
Remember to use a A4 80g, not a busineess card, you are trying to mesure 0,1mm...
by raoulito9
Mon Jan 16, 2017 9:43 pm
Forum: Geeetech Delta Series
Topic: Rostock 301 Layer fan
Replies: 12
Views: 7560

Re: Rostock 301 Layer fan

Hi; Here is what i replied on thingiverse. "Hi Dave. All that you said is correct. I get the same issues. But, the things i printed almost nevet reached the limits that are givent by my fan, and the support can flex a little when touchnig rods. To improve the desing, as you said, we should make a du...
by raoulito9
Mon Jan 09, 2017 5:36 pm
Forum: Extruder
Topic: Rostock 301 extruder motor not able to push filament
Replies: 26
Views: 11677

Re: Rostock 301 extruder motor not able to push filament

Hi. Looks like your head is clogged. Follows the unclogging procedure : Heat hotend to 215 remove bowden Use the specific pin to remove plastic clogged into diamons head. When putting bach bowden, bu sure teflon tube enters more than 5 cm into the aluminium heatsink. Another thing you can trie is to...
by raoulito9
Sat Jan 07, 2017 9:23 pm
Forum: Software
Topic: Slicing with simplify 3d ... Rostock 301 pause on each round
Replies: 8
Views: 4932

Re: Slicing with simplify 3d ... Rostock 301 pause on each r

Missenderstandings.... Metal extruder <> from hotend... This is the piece close to steppers that push filament into bowden. Stock are crappy plastic ones. This will help to push correctly filament. do as you feel I am asking you, for my own tryes, your simplify config files. I did not intend to lear...
by raoulito9
Sat Jan 07, 2017 4:59 pm
Forum: Software
Topic: Slicing with simplify 3d ... Rostock 301 pause on each round
Replies: 8
Views: 4932

Re: Slicing with simplify 3d ... Rostock 301 pause on each r

Hi.
would you share your simplify 3D config files ?
Thank you..

For your pla flow problem :
1 use metal extruders
2 raise vrefs extrudres as high as possible (1.05 for me)
3 heat head at 215 for PLA

Regards.
by raoulito9
Sat Jan 07, 2017 4:54 pm
Forum: Software
Topic: Rostock 301 Bed Levelling
Replies: 9
Views: 7238

Rostock 301 Bed Levelling

My procedure for bed leveling. 1 The bed is attached to the back delta plate with 3 screws with springs. Be sure that it is perfectly level, adjusting the screws, with a caliper or some wedge. 2 Set printer height to 220 on screen printer 3 enter those scripts in repetier (printer config): script1 G...
by raoulito9
Mon Dec 12, 2016 11:25 pm
Forum: Mods And Hacks
Topic: Geeetech Rostock 301, résoudre, solve his problems !!!
Replies: 11
Views: 11047

Re: Geeetech Rostock 301, résoudre, solve his problems !!!

Hi rené. The heat screws kind are "3) Percée plus grande pour recevoir une gaine de Teflon de bout en bout de la vis." So i think they are the best possible to offer the less resistance to PLA, what we are looking for... I must admit i had to cut teflon tube, but i was happy to have some extra teflo...