Search found 40 matches

by JohnQuix
Fri Nov 10, 2017 9:55 am
Forum: Firmware
Topic: Rostock 301 1.0.3 Firmware Problem
Replies: 7
Views: 9342

Re: Rostock 301 1.0.3 Firmware Problem

Using easy print to upgrade to 1.0.3 I tired using the method here on the forums at the end it said FAILED! I can’t remember if there was an error code. I can try to upload 1.0.2 tomorrow to see if there is a specific code. In the meantime since the 1.0.3 firmware is obviously bad should you maybe p...
by JohnQuix
Fri Nov 10, 2017 1:35 am
Forum: Firmware
Topic: Rostock 301 1.0.3 Firmware Problem
Replies: 7
Views: 9342

Re: Rostock 301 1.0.3 Firmware Problem

I uploaded the 1.0.2 firmware and it failed so I had to reload the 1.0.3 firmware which still has the problem after loading it again.
by JohnQuix
Thu Nov 02, 2017 10:12 am
Forum: Firmware
Topic: Rostock 301 1.0.3 Firmware Problem
Replies: 7
Views: 9342

Rostock 301 1.0.3 Firmware Problem

After upgrading to 1.0.3 my printer does not recognize any negative coordinate values. so now it can only travel in the positive areas away from the origin. When I tried to go back to 1.0.2 it bricked my board and I was only able to use EasyPrint to get it back to 1.0.3 which obviously doesn't work.
by JohnQuix
Thu Nov 02, 2017 10:05 am
Forum: Firmware
Topic: New 2017 firmware for rostock 301 ?
Replies: 13
Views: 25051

Re: New 2017 firmware for rostock 301 ?

After upgrading to 1.0.3 my printer does not recognize any negative coordinate values. so now it can only travel in the positive areas away from the origin. When I tried to go back to 1.0.2 it bricked my board and I was only able to use EasyPrint to get it back to 1.0.3 whihch obviously doesn't work...
by JohnQuix
Sat Sep 16, 2017 11:05 pm
Forum: Extruder
Topic: D200 Extruder Temp
Replies: 0
Views: 3829

D200 Extruder Temp

Hello,

My D200 only goes to 230C is there a reason it is limited so low?

I use mostly all MakerGeeks filament and the MakerGeeks PLA temp is 235C, Raptor PLA is 245C, and PETG is 245C.

Is there a technical reason that it won't go over 230C? or was it just a mistake?
by JohnQuix
Tue Feb 21, 2017 11:54 am
Forum: Others
Topic: Rostock 301 Intermittent Pausing
Replies: 3
Views: 6608

Re: Rostock 301 Intermittent Pausing

It's not the slicer.

Happens on Slic3r and Simplify3D and it also happens printing from SD and through USB through Repetier.
by JohnQuix
Fri Feb 17, 2017 4:10 am
Forum: Others
Topic: Rostock 301 Intermittent Pausing
Replies: 3
Views: 6608

Rostock 301 Intermittent Pausing

Hello,

My Rostock 301 pauses every layer leaving big blobs of filament wherever it stops. How do I fix this? Is it just a firmware issue?
by JohnQuix
Fri Feb 17, 2017 4:07 am
Forum: Control Board
Topic: GTM32 Firmware
Replies: 0
Views: 3599

GTM32 Firmware

Hello, There have been quite a few problems noted about the Rostock 301 and the GTM32 board specifically. I was told by Geeetech staff that it uses Marlin which is open source. This means that like many of your other printers the user could easily fix these problems themselves if there was an easy w...
by JohnQuix
Fri Feb 17, 2017 4:00 am
Forum: Products FAQ
Topic: Geeetech GTM32 Pro, Marlin STM32, 32 bits ?
Replies: 1
Views: 7716

Re: Geeetech GTM32 Pro, Marlin STM32, 32 bits ?

I would like an answer to this as well. I have had nothing but trouble with the GTM32 board on my 301.

Mine stops for a half of a second every layer and just dumps filament in that spot before moving on to the next layer.
by JohnQuix
Wed Jan 04, 2017 10:20 pm
Forum: Firmware
Topic: Rostock 301, new firmware changelog
Replies: 17
Views: 27176

Re: Rostock 301, new firmware changelog

I want to do exactly the same thing except with single extrusion. I haven't had much luck with the "diamond" nozzle and at this point I want to just use it with one extruder with a regular E3D type nozzle.

Is there a way to just connect the GTM32 to Arduino IDE and upload new firmware?