Search found 3979 matches

by William
Fri Aug 23, 2019 5:54 pm
Forum: Control Board
Topic: Damaged/faulty Sanguino board
Replies: 1
Views: 37

Re: Damaged/faulty Sanguino board

Hi, Can you provide a specific picture?
If it is not working properly, you can contact your sales to replace it.
by William
Fri Aug 23, 2019 5:52 pm
Forum: Geeetech I3 Pro B
Topic: 3DTouch Z-Offset Adjustment
Replies: 4
Views: 53

Re: 3DTouch Z-Offset Adjustment

Hi, Can you provide a specific video?
So that we can solve the problem better.
by William
Fri Aug 23, 2019 5:50 pm
Forum: Geeetech A30 Series
Topic: Cant assemble block after receiving part
Replies: 1
Views: 35

Re: Cant assemble block after receiving part

Hi,the Y1-X2
Y2-X1
Y3-X4
Y4-X3
And B1-A4
B2-A1
C1(red -A3
black-A2)
I hope this can help you.
by William
Fri Aug 23, 2019 4:14 pm
Forum: Geeetech I3 Pro B
Topic: 3DTouch Z-Offset Adjustment
Replies: 4
Views: 53

Re: 3DTouch Z-Offset Adjustment

Hi, For specific operations on firmware modification and calibration, you can refer to this:http://www.geeetech.com/wiki/index.php/ ... ing_Sensor
I hope this can help you.
by William
Fri Aug 23, 2019 9:46 am
Forum: Geeetech A10 Series
Topic: new guy here... I have a a question about t a greetech a10m
Replies: 2
Views: 73

Re: new guy here... I have a a question about t a greetech a10m

Hi, You can check if the line has a standard for it,
or you can provide its specific connection location and specific picture.
I hope this can help you.
by William
Fri Aug 23, 2019 9:44 am
Forum: Extruder
Topic: Acrylic Geeetech i3 pro c not extruding
Replies: 1
Views: 49

Re: Acrylic Geeetech i3 pro c not extruding

Hi, You can try 1. Only exchange the other end of the shaft motor line to the motor terminal of the extruder (do not change the wiring position on the mainboard) to determine whether the motor line is damaged or not. 2. If the extruder motor still fails to operate after the above operation, the posi...
by William
Fri Aug 23, 2019 9:38 am
Forum: Geeetech I3 Pro W
Topic: pro W won't boot
Replies: 2
Views: 64

Re: pro W won't boot

Hi,You can check the following operation 1. Reconnect the screen cable, which may be caused by loose wiring and poor screen contact; 2. Reconnect the screen line and still display the black block, you can refresh the firmware again. The firmware connection is as follows:http://www.geeetech.com/forum...
by William
Fri Aug 23, 2019 9:33 am
Forum: Geeetech A10 Series
Topic: poor instructions
Replies: 1
Views: 63

Re: poor instructions

Hi, Are you referring to the outer cover on the extruder?
You can use a tool to fasten the bearing wheel to the rail.
by William
Fri Aug 23, 2019 9:28 am
Forum: Geeetech I3 Pro B
Topic: Prints stopping halfway through!!
Replies: 1
Views: 51

Re: Prints stopping halfway through!!

Hi, You can check if the thermistor wiring of your hot end is fully connected. Are you printing via sd card? Or use USB to connect to the printer and slice software for printing? Printing via sd card maybe your motherboard problem; Printing via a USB connection may be caused by hitting the USB line ...