Search found 20 matches

by mava70
Fri Jan 22, 2016 1:12 am
Forum: Firmware
Topic: Reflash Bootloader on GT2560
Replies: 37
Views: 99541

Re: Reflash Bootloader on GT2560

Hi,

My board was fautly checking with oscilloscope the oscillator I don't have any signal. Swapped oscillator but nothing, I fear you have same problem.

Marco
by mava70
Wed Nov 25, 2015 3:15 pm
Forum: Extruder
Topic: Videos of MK8 Extruder assembly
Replies: 6
Views: 36370

Re: Videos of MK8 Extruder assembly

Hello there is a small hex screw next to the hole in the back but I tryed to turn clockwise the screw go inside the hole a lot but don't fix. Should I turn a lot more?
by mava70
Wed Nov 25, 2015 5:29 am
Forum: Extruder
Topic: Videos of MK8 Extruder assembly
Replies: 6
Views: 36370

Re: Videos of MK8 Extruder assembly

hello the heater and the thermistor move inside the hole out and in, can be fixed someway?
by mava70
Wed Nov 25, 2015 5:24 am
Forum: LCD Panel
Topic: Lcd problem when connected to ramps
Replies: 3
Views: 9096

Re: Lcd problem when connected to ramps

solved smart connector connectors are mounted reversed swapped cable now is ok
by mava70
Tue Nov 24, 2015 5:18 pm
Forum: LCD Panel
Topic: Lcd problem when connected to ramps
Replies: 3
Views: 9096

Re: Lcd problem when connected to ramps

Yes the firmware is correct your firmware for rakps board prusa b and it works very well when lcd disconnected.
Lcd is correctly configured in config.h same as gt2560 firmware
by mava70
Tue Nov 24, 2015 4:11 pm
Forum: LCD Panel
Topic: Lcd problem when connected to ramps
Replies: 3
Views: 9096

Lcd problem when connected to ramps

Hello I have had a gt2560 with 2004 lcd. Gt2560 is brocken so I swapped with a standard ramps/2560. Ai have to buy a standard lcd adapter on ebay for connecting 2004 to ramps. When I connect the lcd ribbon Printer stop working and on pc I see a mintemp error reached. Lcd doesn't work but is correctl...
by mava70
Tue Nov 17, 2015 9:39 pm
Forum: Software
Topic: Adjusting belt length
Replies: 1
Views: 5983

Re: Adjusting belt length

change value in eeprom settings until your printer move 100mm when you command a 100mm x or y move. I did this on a trial by error

Marco
by mava70
Tue Nov 17, 2015 9:29 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 388
Views: 16777215

Re: firmware for geeeteh 3D printers

Hello,

is it possibile to update Marlin firmware downloading it from github and allineate config.h from your config and new Marlin firmware? Did you do some kind of code personalization in you firmware outside of config.h?

I am interested in RAMPS version.

Thanks

Marco
by mava70
Mon Nov 09, 2015 9:49 pm
Forum: Firmware
Topic: Substitute gt2560 with mega 2560 ramps 1.4
Replies: 5
Views: 11301

Re: Substitute gt2560 with mega 2560 ramps 1.4

Done,

thank you, I am printing now.

thanks
by mava70
Sat Nov 07, 2015 2:41 am
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 388
Views: 16777215

Re: firmware for geeeteh 3D printers

hello in PI3B-ramps.rar there is not Marlin.ino how to compile?

thanks