Search found 11 matches

by jaitas
Fri Dec 04, 2015 5:04 am
Forum: Resoures Sharing
Topic: Printer parts STL file - Prusa i3 pro C
Replies: 15
Views: 21871

Printer parts STL file - Prusa i3 pro C

Hello is it possible for you to link or provide printable parts for prusa i3 pro C printer (dual extruder version)? I would like to print spares, because it seems that some of my plastic parts are breaking apart. thank you in advance for your answer. (tried to search the forums but didn't find a thr...
by jaitas
Fri Oct 23, 2015 10:53 pm
Forum: Others
Topic: Prusa i3 pro C - dual extruder not starting up
Replies: 8
Views: 7631

Re: Prusa i3 pro C - dual extruder not starting up

Hello I have not had any luck in solving my problem with the prusa i3 pro C not starting up. Friend suggested to use the bootloader method in uploading the firmware. Is this type of uploading possible? And if yes are there schematics for the GT2560 board how to connect wires for the bootloader method?
by jaitas
Thu Oct 15, 2015 4:50 am
Forum: Others
Topic: Prusa i3 pro C - dual extruder not starting up
Replies: 8
Views: 7631

Re: Prusa i3 pro C - dual extruder not starting up

Hello 1.) I have tried now to unplug every wire except the USB -> It still times out when I press upload. If I however choose a programmer AVR ISP and then select upload using programmer it will return with a following error: avrdude: stk500_getsync(): not in sync: resp=0x00 attachment: should I use...
by jaitas
Tue Oct 13, 2015 4:54 am
Forum: Others
Topic: Prusa i3 pro C - dual extruder not starting up
Replies: 8
Views: 7631

Re: Prusa i3 pro C - dual extruder not starting up

I can install a USB Serial port driver using that instructions but with that driver installed it always times out in the "uploading" phase of the process. I will attach a txt file with the error messages that arduino 1.0.1 shows after the process is finally terminated. If I on the other hand try to ...
by jaitas
Sun Oct 11, 2015 11:39 pm
Forum: Others
Topic: Prusa i3 pro C - dual extruder not starting up
Replies: 8
Views: 7631

Re: Prusa i3 pro C - dual extruder not starting up

Hello I contacted your tech support and they pointed me already to that direction. Right now my problem is that I cannot seem to upload firmware or to get arduino working with the printer at all. When I manually install the correct drivers you had mentioned in the thread windows displays it as a mal...
by jaitas
Sun Sep 27, 2015 10:27 pm
Forum: Others
Topic: Prusa i3 pro C - dual extruder not starting up
Replies: 8
Views: 7631

Prusa i3 pro C - dual extruder not starting up

Hello My prusa i3 pro C has stopped starting up. LCD panel shows only two rows of black bars and the reset button doesn't work. - I have tried to connect to the printer via repetetier and octoprint - I have tried to turn it off and on again :) - LCD panel shows only two black bars - I have tried to ...
by jaitas
Fri Sep 25, 2015 3:38 pm
Forum: Firmware
Topic: prusa i3 pro C - have to execute M502 at every start-up
Replies: 1
Views: 2046

prusa i3 pro C - have to execute M502 at every start-up

Hello I have a problem with prusa i3 pro C dual extruder printer. I have to execute M502 command at every start up to start filament to feed, If I wont run that M502 (reset to factory defaults) extruder feeds filament about ten times less than needed (basically none) I have tested with repetetier an...
by jaitas
Fri Sep 25, 2015 3:34 pm
Forum: Mods And Hacks
Topic: Mk8 Extruder - filament jams in the throat.
Replies: 12
Views: 28918

Re: Mk8 Extruder - filament jams in the throat.

Hello Posting a reply because I have just the same problem with my prusa i3 pro C dual extruder version (I believe that's also Mk8, even though I only have one fan and website lists that extruder with two fans) So basically extruder randomly jams (probably in the throat section) and starts to either...
by jaitas
Wed Aug 26, 2015 7:12 pm
Forum: Extruder
Topic: Prusa i3 pro C - dual extruder extruder offset fine tuning
Replies: 13
Views: 13826

Re: Prusa i3 pro C - dual extruder extruder offset fine tuni

Hello I managed to find a good solution by applying extruder offset settings via setting g-code strings to the printer. You can sen g-code lines to printer with repetetier host. 1. send command "M218" -> it will return your current extruder offsets and using that information you can calculate your n...
by jaitas
Mon Aug 24, 2015 2:48 pm
Forum: Extruder
Topic: Prusa i3 pro C - dual extruder extruder offset fine tuning
Replies: 13
Views: 13826

Re: Prusa i3 pro C - dual extruder extruder offset fine tuni

Hello Here's a picture attached showing the slight misalignment. It's most visible in the wipe tower highlighted in red. X axis has about 0.7mm and Y axis about 0.5mm I don't remember the exact measurements right now. And it seems that setting extruder offsets either in Cura or Repetetier won't have...