Search found 48 matches
- Sat Mar 11, 2017 8:48 pm
- Forum: Products FAQ
- Topic: 3dtouch snsor
- Replies: 0
- Views: 3729
3dtouch snsor
I added 3d touch sensor to my I3X printer.Its wors .But one major problem is the hot end level and 3d touch needle level is same. When print start sensor removing print.pls tell me how to fix this?
- Fri Mar 10, 2017 11:31 pm
- Forum: Products FAQ
- Topic: 3d touch snsor
- Replies: 1
- Views: 4632
3d touch snsor
I added 3d touch sensor to my I3X printer.Its wors .But one major problem is the hot end level and 3d touch needle level is same. When print start sensor removing print.pls tell me how to fix this?
- Mon Mar 06, 2017 12:59 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617145
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
Hi My noozzel hot end point and 3d touch sensor point is same level.So when noozel prints sensor will remove.How to fix this please anybody letme know. Thanks advance <blockquote class="imgur-embed-pub" lang="en" data-id="a/KHtxG"><a href="//imgur.com/KHtxG"></a></blockquote><script async src="//s.i...
- Sat Jan 21, 2017 11:39 am
- Forum: Products FAQ
- Topic: GT 2560 3pin modification for BL touch sensor
- Replies: 7
- Views: 20473
Re: GT 2560 3pin modification for BL touch sensor
I fixed it,the third pin not solder proper.i re solder that.now its working.thanks
- Sun Jan 15, 2017 2:30 am
- Forum: Stepper Motor
- Topic: Stepper motor getting toomuh heat
- Replies: 2
- Views: 6437
Re: Stepper motor getting toomuh heat
Hi
I have check voltage as shown in your link.It shows 5.3volt and 11.9 volt.I think some other problem.
I have check voltage as shown in your link.It shows 5.3volt and 11.9 volt.I think some other problem.
- Tue Jan 10, 2017 11:46 pm
- Forum: Stepper Motor
- Topic: Stepper motor getting toomuh heat
- Replies: 2
- Views: 6437
Stepper motor getting toomuh heat
Hi
I replaced Stepper drive for my I3ProX.My all stepper motors getting too much heat about 70c if I run continue 45 minutes .I cant touch that.What is problem how to correct it?
If it is problem of current(I am using A4988) how to adjust and what current output should go to each stepper?
Thanks
Shiva
I replaced Stepper drive for my I3ProX.My all stepper motors getting too much heat about 70c if I run continue 45 minutes .I cant touch that.What is problem how to correct it?
If it is problem of current(I am using A4988) how to adjust and what current output should go to each stepper?
Thanks
Shiva
- Tue Jan 10, 2017 2:18 am
- Forum: Products FAQ
- Topic: Stepper getting very heat
- Replies: 0
- Views: 3326
Stepper getting very heat
Hi
I replaced Stepper drive for my I3ProX.My all stepper motors getting too much heat about 70c if I run continue 45 minutes .I cant touch that.What is problem how to correct it?
If it is problem of current(I am using A4988) how to adjust and what current output should go to each stepper?
I replaced Stepper drive for my I3ProX.My all stepper motors getting too much heat about 70c if I run continue 45 minutes .I cant touch that.What is problem how to correct it?
If it is problem of current(I am using A4988) how to adjust and what current output should go to each stepper?
- Sun Jan 08, 2017 11:27 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617145
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
Ya,I soldered backside also .I made small hole and through hole i put the pin and soldered.Please tell me how to check it properly sold?any particular signal or current will come?
- Sun Jan 08, 2017 2:38 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617145
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
Hi Ajey
pls check attached image in 1st image i soldered 3rd pin.In second picture wiring.I onneted Black-Brown,Green-Orange,Blue-Red and in 2 pin section connected Blue-Black and Red-White.
pls check attached image in 1st image i soldered 3rd pin.In second picture wiring.I onneted Black-Brown,Green-Orange,Blue-Red and in 2 pin section connected Blue-Black and Red-White.
- Sun Jan 08, 2017 1:54 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617145
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
hi,
I am using I3 pro X.I soldered 3rd pin as per instruction and also updated frimware.When i connected sensor not working.Pls some body help me.Pls let me know how to test 3rd pin properly placed or soldered?
Thanks in advance
Shiva
I am using I3 pro X.I soldered 3rd pin as per instruction and also updated frimware.When i connected sensor not working.Pls some body help me.Pls let me know how to test 3rd pin properly placed or soldered?
Thanks in advance
Shiva