Search found 15 matches

by jfsgi
Fri Jul 03, 2015 10:23 pm
Forum: Extruder
Topic: Upgrading to Bowden Extruder
Replies: 9
Views: 6083

Re: Upgrading to Bowden Extruder

Ok, so the fan works now, or just turns on.

I can not get the extruder to a temperature above 220 degrees. As such I can not print with it - WHY WILL IT NOT GO HOT ENOUGH TO DO ANYTHING WITH!!!!

PROVIDE SUPPORT OR I WILL REQUEST A REFUND

please advise
by jfsgi
Thu Jul 02, 2015 7:43 pm
Forum: Extruder
Topic: Upgrading to Bowden Extruder
Replies: 9
Views: 6083

Re: Upgrading to Bowden Extruder

Well the fan is where it came pre-mounted, having said that it is not wired as you provided a fan with a 2 pin fan knowing I have a 3 pin controller. So I have now tried the other extruder I purchased to see if I had a bad one and get the same results. Please advise or replace the two extruder assme...
by jfsgi
Wed Jul 01, 2015 7:44 pm
Forum: Extruder
Topic: Upgrading to Bowden Extruder
Replies: 9
Views: 6083

Re: Upgrading to Bowden Extruder

I can not get the temp to go passed 215, Do you think we have a bad extruder?

Please advise
by jfsgi
Tue Jun 30, 2015 10:26 am
Forum: Extruder
Topic: Upgrading to Bowden Extruder
Replies: 9
Views: 6083

Re: Upgrading to Bowden Extruder

Ok,

That said it looks like I can not get the extruder to extrude filament then. It goes through the stepper motor ok but will not extrude. I cannot even force push the filament into the head it seems to either be blocked or not hot enough to melt the filament.

Please advise,

Jason
by jfsgi
Mon Jun 29, 2015 8:01 pm
Forum: Extruder
Topic: Upgrading to Bowden Extruder
Replies: 9
Views: 6083

Upgrading to Bowden Extruder

I purchased the -Assembled JIETAI GT9L Extruder- and would like to switch out the stock extruder on my prusa I3. Would you please give me the firmware update that I would need for it?

I have this control board GT2560 3D printer controller board.

Thanks
by jfsgi
Tue Jun 16, 2015 11:26 am
Forum: LCD Panel
Topic: LCD 12864 with GT2560
Replies: 29
Views: 36009

LCD 12864 with GT2560

How do I utilize the LCD 12864 with the GT2560 Controller?

Currently I am using the standard LCD,

In the technical specs it lists the ability to use both monitors.

Please advise
by jfsgi
Tue Jun 16, 2015 9:20 am
Forum: Control Board
Topic: Y- Axis Failing
Replies: 17
Views: 7260

Re: Y- Axis Failing

Loading via the lower version seemed to work,

I also have a problem with the slicer

I attached a photo of the issue

Please advise
by jfsgi
Mon Jun 15, 2015 7:29 pm
Forum: Control Board
Topic: Y- Axis Failing
Replies: 17
Views: 7260

Re: Y- Axis Failing

1.6.4
by jfsgi
Mon Jun 15, 2015 11:08 am
Forum: Control Board
Topic: Y- Axis Failing
Replies: 17
Views: 7260

Re: Y- Axis Failing

All of the files are loaded into audrinio, 73 total
by jfsgi
Mon Jun 15, 2015 9:37 am
Forum: Control Board
Topic: Y- Axis Failing
Replies: 17
Views: 7260

Re: Y- Axis Failing

I got the error while trying to upload the firmware>

I loaded the .ino file into the software and clicked upload. (I think there was a total of 73 files that loaded in the Arudiono for the upload