Search found 23 matches

by johnz
Wed Mar 16, 2016 2:31 am
Forum: Mods And Hacks
Topic: Z motors dont move up when printing(M8x2mm leadscrews).
Replies: 13
Views: 24380

Re: Z motors dont move up when printing.

ok this is the kind of I have .. M8 x 2 Trapezoidal thread ..im going to do some more search on how to set it up??
by johnz
Sun Mar 13, 2016 4:39 am
Forum: Mods And Hacks
Topic: Z motors dont move up when printing(M8x2mm leadscrews).
Replies: 13
Views: 24380

Re: Z motors dont move up when printing.

Not much of a guide?? Where In the firmware do I find this or how do I adjust it









/
/
by johnz
Fri Mar 11, 2016 9:52 am
Forum: Mods And Hacks
Topic: Z motors dont move up when printing(M8x2mm leadscrews).
Replies: 13
Views: 24380

Re: Z motors dont move up when printing.

One of my rods bent so I bought 2 of these will that make a difference??
by johnz
Wed Mar 09, 2016 10:29 pm
Forum: Mods And Hacks
Topic: Z motors dont move up when printing(M8x2mm leadscrews).
Replies: 13
Views: 24380

Re: Z motors dont move up when printing.

yes the homing is good everything homes good all motors except the z axis wont move up when printing..??
by johnz
Wed Mar 09, 2016 1:21 pm
Forum: Mods And Hacks
Topic: Z motors dont move up when printing(M8x2mm leadscrews).
Replies: 13
Views: 24380

Z motors dont move up when printing(M8x2mm leadscrews).

I have a geetech Acrylic i3 with the GT2560 board I put the I3X single extruder firmware. Everything works except when i go to print the Z motors don't move up as it is printing they just stay at one layer and don't move UP...pleas any HELP..??? thanks.
by johnz
Tue Jan 26, 2016 10:45 pm
Forum: Firmware
Topic: firmware
Replies: 4
Views: 7404

Re: firmware

also it wont print in the center, it prints on the side of the bed???
by johnz
Tue Jan 26, 2016 10:39 pm
Forum: Firmware
Topic: firmware
Replies: 4
Views: 7404

Re: firmware

I did all that ,now my prints come out real small?? I did not change anything in Repetier as it was working great with the other board.
by johnz
Tue Jan 26, 2016 1:24 pm
Forum: Firmware
Topic: firmware
Replies: 4
Views: 7404

firmware

Hello I have a Prusa Reprap Acrylic i3 it had a sanguinololu board but now I want to replace it with a GT2560 board ...what firmware should I flash the Gt2560 to work with the printer ??? please help....Thanks.
by johnz
Fri Dec 11, 2015 12:37 pm
Forum: Others
Topic: Mosfet problem
Replies: 37
Views: 41670

Re: Mosfet problem

No the MOSFET is fried...Not working...check everything ...everything works except the hot bed!!! Just bought this in May 13, 2015 ....Cant believe it just fried like that,,,Damn!!
by johnz
Fri Dec 11, 2015 6:44 am
Forum: Others
Topic: Mosfet problem
Replies: 37
Views: 41670

Re: Mosfet problem

The Heat bed stopped working and then I looked at the board and this is what it looks like and the heat bed reading in pic 2.