Search found 46 matches
- Tue Dec 01, 2015 8:12 am
- Forum: Extruder
- Topic: The Ultimate solution to all extruder problems
- Replies: 0
- Views: 3690
The Ultimate solution to all extruder problems
After nearly 12 month of jams and blockages and failed prints i have found the key to fixing the mk8 extruder problem! scrap it and buy a new one from a different company. I brought the makerfarm Greg's extruder and the ed3-v6 hot end and all my troubles are over. I get excellent quality prints and ...
- Thu Oct 01, 2015 8:57 pm
- Forum: Mods And Hacks
- Topic: Mk8 Extruder - filament jams in the throat.
- Replies: 12
- Views: 63322
Re: Mk8 Extruder - filament jams in the throat.
I have done all that. Multiple times. The system works until the filament jams in the throat. The guides are aligned.
- Tue Sep 22, 2015 6:06 pm
- Forum: Mods And Hacks
- Topic: Mk8 Extruder - filament jams in the throat.
- Replies: 12
- Views: 63322
Mk8 Extruder - filament jams in the throat.
ok so the extruder works. however the extruder jams and the filament jams in the throat. the motor starts clicking randomly during printing. If i pause the print i can force the filament pass the jam and then the pla flows freely, however the filament will eventually jam again. If i am reverse the e...
- Mon Jul 20, 2015 1:48 pm
- Forum: Extruder
- Topic: Prusa i3 acrylic extruder ticking
- Replies: 44
- Views: 56753
Re: Prusa i3 acrylic extruder ticking
I Have had all these problems also, its seems the mark 8 extruder is just shit in general. I have had some patchy success but a lot of failure. i have been trying for 6 months the rest of the printer is fine just the bloody extruder
- Thu Mar 12, 2015 5:51 pm
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
at 210 the e truder motor still skips, 220 is about the minimum i can use successfully
- Thu Mar 12, 2015 5:18 pm
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
i have tried multiple stl files.
- Thu Mar 12, 2015 4:01 pm
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
if i try to run at 200 it will not extrude at all. As is show in the picture i am attaching shows i get excellent prints till between 20 - 35 layers and then the extruder seems to block and the flow stops and I get stringy melted plastic instead of nice orderly prints.
- Thu Mar 12, 2015 8:51 am
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
Ok so once he printer has made a few layers I should dole he temp back down to 200?
- Wed Mar 11, 2015 8:04 pm
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
i am runnign at 230deg for PLA
- Wed Mar 11, 2015 4:58 pm
- Forum: Stepper Motor
- Topic: acrylic I3 motor issues
- Replies: 68
- Views: 93173
Re: acrylic I3 motor issues
that has helped a lot, however my extruder still seems to randomly get blocked after about 20 layers of infill